PIC18F66J15-I/PT Microchip Technology, PIC18F66J15-I/PT Datasheet - Page 261

• Manufacturer Part Number: PIC18F66J15-I/PT
• Description: IC PIC MCU FLASH 48KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F66J15-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 96KB (48K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

20.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep, or any
Idle mode and bit, SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREGx register; if the RCxIE enable bit is set, the
interrupt generated will wake the chip from the
Low-Power mode. If the global interrupt is enabled, the
program will branch to the interrupt vector.
TABLE 20-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
© 2009 Microchip Technology Inc.
INTCON
PIR1
PIE1
IPR1
PIR3
PIE3
IPR3
RCSTAx
RCREGx
TXSTAx
BAUDCONx ABDOVF
SPBRGHx
SPBRGx
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Name
EUSART SYNCHRONOUS SLAVE
RECEPTION
EUSARTx Receive Register
EUSARTx Baud Rate Generator Register High Byte
EUSARTx Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
SSP2IE
SSP2IP
SSP2IF
PSPIF
PSPIE
PSPIP
CSRC
SPEN
Bit 7
BCL2IF
BCL2IE
BCL2IP
RCIDL
ADIF
ADIE
ADIP
Bit 6
RX9
TX9
RC1IE
RC1IP
RC2IE
RC2IP
RC1IF
RC2IF
SREN
TXEN
Bit 5
—
INT0IE
TX1IE
TX1IP
TX2IE
TX2IP
CREN
SYNC
TX1IF
TX2IF
SCKP
Bit 4
PIC18F87J10 FAMILY
TMR4IF
TMR4IE
TMR4IP
SSP1IF
SSP1IE
SSP1IP
ADDEN
SENDB
BRG16
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
RBIE
Bit 3
Enable the synchronous master serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
If interrupts are desired, set enable bit, RCxIE.
If 9-bit reception is desired, set bit, RX9.
To enable reception, set enable bit, CREN.
Flag bit, RCxIF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RCxIE, was set.
Read the RCSTAx register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREGx register.
If any error occurred, clear the error by clearing
bit, CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP1IF
CCP1IE
CCP1IP
CCP5IF
CCP5IE
CCP5IP
BRGH
FERR
Bit 2
—
TMR2IE
TMR2IP
TMR2IF
CCP4IF
CCP4IE
CCP4IP
INT0IF
OERR
TRMT
WUE
Bit 1
TMR1IE
TMR1IP
TMR1IF
CCP3IF
CCP3IE
CCP3IP
ABDEN
RX9D
TX9D
RBIF
DS39663F-page 259
Bit 0
on page
Values
Reset
53
55
55
55
55
55
55
55
55
55
56
56
56