RF6001_1 RFMD [RF Micro Devices], RF6001_1 Datasheet - Page 69

• Manufacturer Part Number: RF6001_1
• Description: FRACTIONAL-N RF SYNTHESIZER WITH MODULATOR AND DIGITAL IF FILTER
• Manufacturer: RFMD [RF Micro Devices]

Rev A3 DS050929
Rev A0 040930
Rev A2 050602
Rev A3 050929
Rev A1 041118
Prelim 040414
Prelim 040310
Prelim 040317
Rev
Admin
Eng
JM
JM
PB
LY
LY
LY
Specification Table
Power Supply, Maximum Current by Pin: added four rows under this heading.
Application Information
Power Supplies and Control Signals: replaced with “General Purpose Output Control” and “Power Supplies and
Register Tables
RF6001 Register Map, Calibration (CAL): changed data from “CAL5(17:0)” to “CAL(17:0)”.
RF6001 Register Map, TX Data (TXDT): deleted row.
RF6001 Register Map, Calibration 2 (CAL2): added row.
RF6001 Register Map, BLANK (BLANK): added row.
RF6001 Register Map, DELAY (DELAY): added row.
RF6001 Register Map, D_FILL (D_FILL): added row.
RF6001 Register Map, TX_DLY (TX_DLY): added row.
Initial Datasheet. (Based on 6001-29, revision code Prelim 040309.) Reasons for new revision:
• Improved OSCO driver swing and load capability. (The level of the clock drive was too low into the capacitive
• The TXDT register was removed.
• Changed default value of TLOCK to “3’d3”.
• Added MSKSEL bit in CFG1(11).
• PLL and phase detector changes to improve slew rate and overall settle time. (KV_DEF is now used for KV_VAL
• AFC DAC output is tri-stated when DAC2EN bit is low.
Specification Table
PLL Specification, Frequency Range, internal: added line with min specification of “0MHz” and max specification
PLL Specification, Frequency Range, FIN Pin: existing line with min specification of “0MHz” and max specification
Oscillator Output Buffer, Output Voltage (V
Oscillator Output Buffer, Load Capacitance: changed min specification from “1pF” to “5pF”, and max specifica-
DAC1 and DAC2 Specifications, DAC2 (AFC) Tri-State Output Impedance: added.
Application Information
Transmit Modulation Interface Digital Mode: added second and fourth paragraphs.
Addition of Delay on MCK: added.
Transmit Test Modes: changed to “Transmit Test Mode”; first paragraph updated to reflect single test mode, and
Register Tables
CFG1, CFG1(11:10): changed to “CFG1(10)”.
CFG1, CFG1(11): added as “MCKSEL” bit.
PLLx1, PLLLx1(11:9): default value changed from “0” to “3h”.
TXDT: table removed.
Application Information
Synthesizer Information, VCO’s: replaced two paragraphs following table with one paragraph; updated diagram.
Banner: Changed from “Proposed” to “Preliminary”.
PCB Design Requirements: added.
Banner: “Preliminary” banner removed.
Trademark Information: added.
Application Information
Analog I/Q Mode: replaced first paragraph with seven new paragraphs and a table.
Register Tables
TXMOD, TXMOD(7:4): changed equation.
TXMOD, TXMOD(3:0): changed equation.
“RoHS-Compliant & Pb-Free” notation and RoHS information added.
Control Signals”.
load which was presented to it by some customers. The specification on this revision is to be able to drive a
capacitive load up to 30pF.)
during KV calibration.)
of “2100MHz”.
of “550MHz”.
tion from “10pF” to “30pF”.
“TXTEST=1, TXTM=0” added to first paragraph; “TXTEST=1, TXTM=1” section removed.
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at ([phone] or [e-mail].
Revision Data
OUT
): changed min specification from “600mV
Changes
Part of the POLARIS™ TOTAL RADIO™ Solution
P-P
RF6001
” to “800mV
P-P
69 of 70
”.