MCF5272CVF66 Freescale Semiconductor, MCF5272CVF66 Datasheet - Page 66

• Manufacturer Part Number: MCF5272CVF66
• Description: IC MPU 32BIT 66MHZ 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272CVF66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 196-MAPBGA
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Not Compliant

Overview
1.2.2.4
The sleep and stop power management modes reduce power consumption by allowing software to shut
down the core, peripherals, or the whole device during inactive periods. To reduce power consumption
further, software can individually disable internal clocks to the on-chip peripheral modules. The
power-saving modes are described as follows:
1.2.2.5
The MCF5272 has up to three 16-bit general-purpose parallel ports, each line of which can be programmed
as either an input or output. Some port lines have dedicated pins and others are shared with other MCF5272
functions. Some outputs have high drive current capability.
1.2.2.6
The MCF5272 has flexible latched interrupt inputs each of which can generate a separate, maskable
interrupt with programmable interrupt priority level and triggering edge (falling or rising). Each interrupt
has its own interrupt vector.
1.2.3
The MCF5272 has two full-duplex UART modules with an on-chip baud rate generator providing both
standard and non-standard baud rates up to 5 Mbps. The module is functionally equivalent to the MC68681
DUART with enhanced features including 24-byte Tx and Rx FIFOs. Data formats can be 5, 6, 7, or 8 bits
with even, odd, or no parity and up to 2 stop bits in 1/16-bit increments. Receive and transmit FIFOs
minimize CPU service calls. A wide variety of error detection and maskable interrupt capability is
provided.
Using a programmable prescaler or an external source, the MCF5272 system clock supports various baud
rates. Modem support is provided with request-to-send (RTS) and clear-to-send (CTS) lines available
externally. Full-duplex autoecho loopback, local loopback, and remote loopback modes can be selected.
1-6
•
•
Sleep mode uses interrupt control logic to allow any interrupt condition to wake the processor. As
the MCF5272 is fully static, sleep mode is simply the disabling of the core’s clock after the current
instruction completes. An interrupt from any internal or external source causes on-chip power
management logic to reenable the core’s clock; execution resumes with the next instruction. This
allows rapid return from power-down state as compared to a dynamic implementation that must
perform power-on reset processing before software can handle the interrupt request. If interrupts
are enabled at the appropriate priority level, program control passes to the relevant interrupt service
routine.
Stop mode is entered by the disabling of the external clock input and is achieved by software setting
a bit in a control register. Program execution stops after the current instruction. In stop mode,
neither the core nor peripherals are active. The MCF5272 consumes very little power in this mode.
To resume normal operation, the external interrupts cause the power management logic to
re-enable the external clock input. The MCF5272 resumes program execution from where it
entered stop mode (if no interrupt are pending), or starts interrupt exception processing if interrupts
are pending.
UART Module
Power Management
Parallel Input/Output Ports
Interrupt Inputs
MCF5272 ColdFire
®
Integrated Microprocessor User’s Manual, Rev. 3
Freescale Semiconductor