PCM18XT0 Microchip Technology, PCM18XT0 Datasheet - Page 200

• Manufacturer Part Number: PCM18XT0
• Description: MODULE PROC PIC18F4685
• Manufacturer: Microchip Technology

Specifications of PCM18XT0

• Accessory Type: Processor Module
• Product: Microcontroller Modules
• Core Processor: PIC18F4685
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: ICE2000
• For Use With: ICE2000 - EMULATOR MPLAB-ICE 2000 POD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Not applicable / Not applicable

PIC18F2682/2685/4682/4685
REGISTER 17-4:
DS39761C-page 200
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3-0
Note 1:
WCOL
R/W-0
2:
When enabled, the SDA and SCL pins must be properly configured as input or output.
Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPBUF register was attempted while the I
0 = No collision
In Slave Transmit mode:
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit.
SSPOV: Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte (must be cleared in
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode.
SSPEN: Master Synchronous Serial Port Enable bit
1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: SCK Release Control bit
In Slave mode:
1 = Release clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode.
SSPM3:SSPM0: Master Synchronous Serial Port Mode Select bits
1111 = I
1110 = I
1011 = I
1000 = I
0111 = I
0110 = I
SSPOV
R/W-0
transmission to be started (must be cleared in software)
software)
software)
SSPCON1: MSSP CONTROL REGISTER 1 (I
2
2
2
2
2
2
C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
C Firmware Controlled Master mode (slave Idle)
C Master mode, clock = F
C Slave mode, 10-bit address
C Slave mode, 7-bit address
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
(1)
R/W-0
CKP
OSC
/(4 * (SSPADD + 1))
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
(1)
(2)
2
C™ MODE)
SSPM2
R/W-0
2
C conditions were not valid for a
(2)
(2)
© 2009 Microchip Technology Inc.
x = Bit is unknown
SSPM1
R/W-0
(2)
SSPM0
R/W-0
bit 0
(2)