aduc7030 Analog Devices, Inc., aduc7030 Datasheet - Page 11

• Manufacturer Part Number: aduc7030
• Description: Integrated Precision Battery Sensor For Automotive
• Manufacturer: Analog Devices, Inc.

Preliminary Technical Data
Parameter
IDD–MCU Powered Down
IDD – MCU Powered Down
IDD – MCU Powered Down
IDD – MCU Powered Down
IDD –Current ADC
IDD –Voltage/Temperature
ADC
IDD – Precision Oscillator
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
These numbers are not production tested, but are guaranteed by design and/or characterization data at production release.
Valid for current ADC gain setting of PGA = 4 to 64.
These numbers include temperature drift.
Tested at gain range = 4; self-offset calibration removes this error.
Measured with an internal short after an initial offset calibration.
Measured with an internal short
These numbers include internal reference temperature drift.
Factory Calibrated at Gain = 1.
System calibration at specific gain range will remove the error at this gain range
input referred noise figures
can also be used to reduce the ADC Input Range (LSB Size).
Includes an initial system calibration
When used in conjunction with ADCREF, the Low Power Mode Reference error MMR.
Using ADC Normal Mode Voltage Reference
Typical Noise in Low Power modes is measured with Chop enabled.
Voltage Channel Specifications include resistive attenuator input stage
System Calibration will remove this error
rms noise is referred to Voltage attenuator input, for example at F
ADC Self Offset calibration will remove this error.
Valid after an initial Self Calibration
System Calibration will remove this error
In ADC Low Power Mode the input range is fixed at ±9.375mV. In ADC Low Power Plus Mode the input range is fixed at ±2.34375mV.
It is possible to extend the ADC input range by up to 10% by modifying the factory set value of the Gain Calibration register or using system calibration. This approach
Limited by minimum absolute input voltage range.
Valid for a differential input less than 10mV
Measured using Box Method
The long-term stability specification is non cumulative. The drift in subsequent 1,000 hour periods is significantly lower than in the first 1,000 hour period.
References of up to REG_AVDD can be accommodated by enabling an internal Divide-by-2
Die Temperature.
Endurance is qualified to 10,000 cycles as per JEDEC Std. 22 method A117 and measured at -40°C, +25°C and +125°C. Typical endurance at 25°C is 170,000 cycles.
Retention lifetime equivalent at junction temperature (Tj) = 85°C as per JEDEC Std. 22 method A117. Retention lifetime will de-rate with junction temperature.
Low Power oscillator can be calibrated against either the precision oscillator or the external 32.768kHz crystal in user code
These numbers are not production tested, but are supported by LIN Compliance testing.
BSD Electrical Specifications, except High and Low voltage levels, are per LIN2.0 with pull-up resistor disabled and C
Specified after Rlimit of 39Ohms
The MCU core is not shutdown but interrupted and high voltage I/O pins are disabled in response to a thermal shutdown event.
Thermal Impedance can be used to calculate the thermal gradient from ambient to die temperature.
Typical, additional supply current consumed during Flash memory program and erase cycles is 7mA and 5mA respectively.
Internal Regulated Supply available at REG_DVDD (I
1
1
1
Test Conditions/Comments
ADC Low Power Mode, measured over an ambient
temperature range of −40°C to +85°C
(Continuous ADC Conversion )
ADC Low Power-Plus Mode, measured over an ambient
temperature range of −10°C to +40°C
(Continuous ADC Conversion )
Average Current, Measured with Wake and Watchdog
Timer clocked from Low Power Oscillator (−40°C to
+85°C)
Average Current, Measured with Wake and Watchdog
Timer clocked from Low Power Oscillator over an
ambient temperature range of −10°C to +40°C
SOURCE
=5mA), and REG_AVDD (I
ADC
=1KHz, typical rms noise at the ADC input is 7.5uV, scaled by the attenuator (24) yields these
Rev. PrE | Page 11 of 150
SOURCE
=1mA)
Min
Load
= 10nF max.
Typ
300
520
120
120
1.7
0.5
400
ADuC7030/ADuC7033
Max
500
700
300
175
Unit
µA
µA
µA
µA
mA
mA
µA