MT90221 Zarlink Semiconductor, MT90221 Datasheet - Page 15

• Manufacturer Part Number: MT90221
• Description: Quad Inverse Multiplexing For Atm (IMA) Device With Flexible Ima And Uni Mode
• Manufacturer: Zarlink Semiconductor

MT90221
Pin Description (continued)
6
87, 89, 92,
80, 83 85,
101, 103,
135, 142,
138, 140,
158, 159,
124, 125,
126, 127,
111, 113
108, 115
144, 150
146, 148
154, 155
160, 161
117,118,
133, 134
98, 106,
94 96,
Pin #
TXSYNCio
RXSYNCi
TXCKi/o
PLLREF
REFCK
RXCKi
Name
[3:0]
[3:0]
[3:0]
[3:0]
[1:0]
[3:0]
NC
I/O
I/O PCM Interface Transmit Clock 3-0. This pin is an input for PCM Modes 2, 4, 5 and
I/O Transmit Line 8KHz Frame Pulse 3-0. This pin is an input for Interface Modes 2,
O Output reference to an external PLL. See 4.3 Description of the PCM Interface
I
I
I
7. It is an output for Interface Modes 1, 3, 6 and 8 (see Section 4.2, PCM System
Interface Modes).
It is the clock for serial PCM data transmission of the T1 and E1 framers. The TXCK
source is software selectable and can be either one of the eight RXCK or one of the
four REFCK signals. It is used for internal transmit timing and should be connected
to the Transmit Clock of the framer.
1. The TXCK is 4.096 MHz for ST-BUS applications.
2. For generic PCM Interfaces (non ST-BUS or asynchronous line termination),
these outputs can be programmed to provide either a 1.544 MHz (T1) or 2.048
MHz (T1 or E1) clock.
4, 5 and 7. It is an output for Interface Modes 1, 3, 6 and 8 (see PCM Section 4.2,
PCM System Interface Modes).
It is the 8 kHz reference used as transmit synchronization for the PCM system
interface. When an output, the TXSYNC is generated from the TXCK signal and is
independent from other TXSYNC signals. Two output modes can be programmed:
1. For ST-BUS applications, it is a low going pulse (F0), that delimits the 32 channel
frame of the ST-BUS interface at DSTi and DSTo lines (see Figure 25 - ST-BUS
Timing Diagram for this sync pulse). The frame pulse is typically received through
the RXSYNC[0] pin.
2. For generic PCM Interfaces, it can be programmed to generate either a positive
or negative pulse polarity that lines up with the first bit of the PCM system interface.
Receive line 8KHz Frame Pulse 3-0. This signal represents the 8 KHz reference
received from the incoming T1 or E1 line. The MT90221 can be programmed to
accept different 8 KHz pulse formats at this input.
1. For ST-BUS applications, it is a low going pulse (F0), which delimits the 32
channel frame of ST-BUS interface at DSTi and DSTo lines. See STBUS timing
diagram for this sync pulse.
2. For generic PCM Interfaces, it can be programmed to accept either positive or
negative pulse polarities.
PCM Interface Receive Clock 3-0. This input line represents the clock for the
receive serial PCM data of the T1 and E1 framers. The T1 or E1 frequency value to
be received at this input clock is defined by the user through an internal register.
1. For ST-BUS applications, input pin RXCKi receives the 4.096 MHz signal.
2. For generic PCM Interfaces, these inputs can be programmed to accept either a
1.544 MHz (T1) or 2.048 MHz (T1 or E1) clock.
for details.
Input reference clock inputs 3 to 0. Receive the de-jittered transmit clock
reference to be internally routed to the T1/E1 framer transmit clocks (output pins
TXCK[3:0]. See “Description of the PCM Interface” on page 23. for more details.
No Connect. Suggest using external pull-up to reduce noise.
Description