SAM7L128 Atmel Corporation, SAM7L128 Datasheet - Page 325

• Manufacturer Part Number: SAM7L128
• Manufacturer: Atmel Corporation

Specifications of SAM7L128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 36 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 80
• Ext Interrupts: 80
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Segment Lcd: 40
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 460
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 6
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.8 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 29-10. Master Read with Multiple Data Bytes
29.7.6
29.7.6.1
6257A–ATARM–20-Feb-08
TXCOMP
RXRDY
TWD
Internal Address
S
7-bit Slave Addressing
Write START Bit
DADR
If an acknowledge is received, the master is then ready to receive data from the slave. After data
has been received, the master sends an acknowledge condition to notify the slave that the data
has been received except for the last data, after the stop condition. See
RXRDY bit is set in the status register, a character has been received in the receive-holding reg-
ister (TWI_RHR). The RXRDY bit is reset when reading the TWI_RHR.
When a single data byte read is performed, with or without internal address (IADR), the START
and STOP bits must be set at the same time. See
performed, with or without internal address (IADR), the STOP bit must be set after the next-to-
last data received. See
Figure 29-9. Master Read with One Data Byte
RXRDY is used as Receive Ready for the PDC receive channel.
The TWI interface can perform various transfer formats: Transfers with 7-bit slave address
devices and 10-bit slave address devices.
When Addressing 7-bit slave devices, the internal address bytes are used to perform random
address (read or write) accesses to reach one or more data bytes, within a memory page loca-
tion in a serial memory, for example. When performing read operations with an internal address,
the TWI performs a write operation to set the internal address into the slave device, and then
switch to Master Receiver mode. Note that the second start condition (after sending the IADR) is
R
A
TXCOMP
DATA n
RXRDY
TWD
Figure
Read RHR
A
S
DATA n
Write START &
29-10. For Internal Address usage see
DATA (n+1)
STOP Bit
DADR
AT91SAM7L128/64 Preliminary
A
DATA (n+1)
Read RHR
R
DATA (n+m)-1
Figure
A
29-9. When a multiple data byte read is
DATA
DATA (n+m)-1
A
Read RHR
after next-to-last data read
DATA (n+m)
Read RHR
Write STOP Bit
Section
N
Figure
P
29.7.6.
29-9. When the
N
DATA (n+m)
Read RHR
P
325