SAM3S16C Atmel Corporation, SAM3S16C Datasheet - Page 85

• Manufacturer Part Number: SAM3S16C
• Manufacturer: Atmel Corporation

Specifications of SAM3S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 100 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 39
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.10.4
12.10.4.1
11117B–ATARM–18-Oct-11
Shift Operations
ASR
If you omit the shift, or specify LSL #0, the instruction uses the value in Rm.
If you specify a shift, the shift is applied to the value in Rm, and the resulting 32-bit value is used
by the instruction. However, the contents in the register Rm remains unchanged. Specifying a
register with shift also updates the carry flag when used with certain instructions. For information
on the shift operations and how they affect the carry flag, see
Register shift operations move the bits in a register left or right by a specified number of bits, the
shift length. Register shift can be performed:
The permitted shift lengths depend on the shift type and the instruction, see the individual
instruction description or
occurs. Register shift operations update the carry flag except when the specified shift length is 0.
The following sub-sections describe the various shift operations and how they affect the carry
flag. In these descriptions, Rm is the register containing the value to be shifted, and n is the shift
length.
Arithmetic shift right by n bits moves the left-hand 32-n bits of the register Rm, to the right by n
places, into the right-hand 32-n bits of the result. And it copies the original bit[31] of the register
into the left-hand n bits of the result. See
You can use the ASR #n operation to divide the value in the register Rm by 2
being rounded towards negative-infinity.
When the instruction is ASRS or when ASR #n is used in Operand2 with the instructions MOVS,
MVNS, ANDS, ORRS, ORNS, EORS, BICS, TEQ or TST, the carry flag is updated to the last bit
shifted out, bit[n-1], of the register Rm.
Figure 12-4. ASR #3
• directly by the instructions ASR, LSR, LSL, ROR, and RRX, and the result is written to a
• during the calculation of Operand2 by the instructions that specify the second operand as a
• If n is 32 or more, then all the bits in the result are set to the value of bit[31] of Rm.
• If n is 32 or more and the carry flag is updated, it is updated to the value of bit[31] of Rm.
destination register
register with shift, see
instruction.
31
LSR #n
ROR #n
RRX
-
logical shift right n bits, 1 ≤ n ≤ 32.
rotate right n bits, 1 ≤ n ≤ 31.
rotate right one bit, with extend.
if omitted, no shift occurs, equivalent to LSL #0.
“Flexible second operand” on page
“Flexible second operand” on page
...
Figure 12-4 on page
42. The result is used by the
“Shift Operations”
42. If the shift length is 0, no shift
43.
5
4
3
2
1 0
SAM3S16
n
, with the result
Carry
Flag
43