SAM3S16C Atmel Corporation, SAM3S16C Datasheet - Page 34

• Manufacturer Part Number: SAM3S16C
• Manufacturer: Atmel Corporation

Specifications of SAM3S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 100 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 39
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.5
Figure 10-2. Clock Generator Block Diagram
34
Clock Generator
SAM3S16
The Slow Clock generator is based on a 32 kHz crystal oscillator and an embedded 32 kHz RC
oscillator. The Slow Clock defaults to the RC oscillator, but the software can enable the crystal
oscillator and select it as the Slow Clock source.
The Supply Controller starts up the device by sequentially enabling the internal power switches
and the Voltage Regulator, then it generates the proper reset signals to the core power supply.
It also enables to set the system in different low power modes and to wake it up from a wide
range of events.
The Clock Generator is made up of:
• One Low Power 32768Hz Slow Clock oscillator with bypass mode
• One Low-Power RC oscillator
• One 3-20 MHz Crystal Oscillator, which can be bypassed
• One Fast RC oscillator factory programmed, 3 output frequencies can be selected: 4, 8 or 12
• One 80 to 240 MHz PLL (PLLB) providing a clock for the USB Full Speed Controller
• One 80 to 240 MHz programmable PLL (PLLA), capable to provide the clock MCK to the
MHz. By default 4 MHz is selected.
processor and to the peripherals. The PLLA input frequency is from 3 to 32 MHz.
XOUT32
XIN32
XOUT
XIN
Management
12/8/4 MHz
Slow Clock
3-20 MHz
Oscillator
RC OSC
Divider A
Controller
Clock Generator
PLL and
Oscillator
PLL and
Divider B
RC OSC
On Chip
On Chip
32 kHz
Power
Status
Main
Control
XTALSEL
Slow Clock
SLCK
Main Clock
MAINCK
MAINSEL
PLLB Clock
PLLBCK
PLLA Clock
PLLACK
11117B–ATARM–18-Oct-11