SAM3S16C Atmel Corporation, SAM3S16C Datasheet - Page 320

• Manufacturer Part Number: SAM3S16C
• Manufacturer: Atmel Corporation

Specifications of SAM3S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 100 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 39
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.3.5.5
21.3.5.6
278
278
SAM3S16
SAM3S16
Flash General-purpose NVM Commands
Flash Security Bit Command
Lock bits can be read using Get Lock Bit command (GLB). The n
n of the bit mask is set..
Table 21-11. Get Lock Bit Command
General-purpose NVM bits (GP NVM bits) can be set using the Set GPNVM command (SGPB).
This command also activates GP NVM bits. A bit mask is provided as argument to the com-
mand. When bit 0 of the bit mask is set, then the first GP NVM bit is activated.
In the same way, the Clear GPNVM command (CGPB) is used to clear general-purpose NVM
bits. The general-purpose NVM bit is deactivated when the corresponding bit in the pattern value
is set to 1.
Table 21-12. Set/Clear GP NVM Command
General-purpose NVM bits can be read using the Get GPNVM Bit command (GGPB). The n
GP NVM bit is active when bit n of the bit mask is set..
Table 21-13. Get GP NVM Bit Command
A security bit can be set using the Set Security Bit command (SSE). Once the security bit is
active, the Fast Flash programming is disabled. No other command can be run. An event on the
Erase pin can erase the security bit once the contents of the Flash have been erased.
Table 21-14. Set Security Bit Command
Once the security bit is set, it is not possible to access FFPI. The only way to erase the security
bit is to erase the Flash.
Step
1
2
Step
1
2
Step
1
2
Step
1
2
Handshake Sequence
Write handshaking
Read handshaking
Handshake Sequence
Write handshaking
Write handshaking
Handshake Sequence
Write handshaking
Read handshaking
Handshake Sequence
Write handshaking
Write handshaking
MODE[3:0]
CMDE
DATA
MODE[3:0]
CMDE
DATA
MODE[3:0]
CMDE
DATA
MODE[3:0]
CMDE
DATA
DATA[15:0]
GLB
Lock Bit Mask Status
0 = Lock bit is cleared
1 = Lock bit is set
DATA[15:0]
SGPB or CGPB
GP NVM bit pattern value
DATA[15:0]
GGPB
GP NVM Bit Mask Status
0 = GP NVM bit is cleared
1 = GP NVM bit is set
DATA[15:0]
SSE
0
th
lock bit is active when the bit
11117B–ATARM–18-Oct-11
11117B–ATARM–18-Oct-11
th