SAM3S16C Atmel Corporation, SAM3S16C Datasheet - Page 12

• Manufacturer Part Number: SAM3S16C
• Manufacturer: Atmel Corporation

Specifications of SAM3S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 100 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 39
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

5. Power Considerations
5.1
5.2
5.3
12
Power Supplies
Voltage Regulator
Typical Powering Schematics
SAM3S16
The SAM3S16 product has several types of power supply pins:
The SAM3S16 embeds a voltage regulator that is managed by the Supply Controller.
This internal regulator is intended to supply the internal core of SAM3S16. It features two differ-
ent operating modes:
For adequate input and output power supply decoupling/bypassing, refer to the Voltage Regula-
tor section in the Electrical Characteristics section of the datasheet.
The SAM3S16 supports a 1.62V-3.6V single supply mode. The internal regulator input con-
nected to the source and its output feeds VDDCORE.
As VDDIN powers the voltage regulator, the ADC/DAC and the analog comparator, when the
user does not want to use the embedded voltage regulator, it can be disabled by software via
the SUPC (note that it is different from Backup mode).
• VDDCORE pins: Power the core, the embedded memories and the peripherals; voltage
• VDDIO pins: Power the Peripherals I/O lines (Input/Output Buffers); USB transceiver; Backup
• VDDIN pin: Voltage Regulator Input, ADC, DAC and Analog Comparator Power Supply;
• VDDPLL pin: Powers the PLLA, PLLB, the Fast RC and the 3 to 20 MHz oscillator; voltage
• In Normal mode, the voltage regulator consumes less than 500 µA static current and draws
• In Backup mode, the voltage regulator consumes less than 1 µA while its output (VDDOUT)
ranges from 1.08V to 1.32V.
part, 32kHz crystal oscillator and oscillator pads; ranges from 1.62V to 3.6V.
Voltage ranges from 1.62V to 3.6V.
ranges from 1.08V to 1.32V.
80 mA of output current. Internal adaptive biasing adjusts the regulator quiescent current
depending on the required load current. In Wait Mode, quiescent current is only 5 µA.
is driven internally to GND. The default output voltage is 1.20V and the start-up time to reach
Normal mode is inferior to 300 µs.
Figure 5-1
shows the power schematics.
11117B–ATARM–18-Oct-11