SAM3S16C Atmel Corporation, SAM3S16C Datasheet - Page 15

• Manufacturer Part Number: SAM3S16C
• Manufacturer: Atmel Corporation

Specifications of SAM3S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 100 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 39
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

5.5.2
5.5.3
11117B–ATARM–18-Oct-11
Wait Mode
Sleep Mode
The purpose of the wait mode is to achieve very low power consumption while maintaining the
whole device in a powered state for a startup time of less than 10 µs.
In this mode, the clocks of the core, peripherals and memories are stopped. However, the core,
peripherals and memories power supplies are still powered. From this mode, a fast start up is
available.
This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in
PMC_FSMR). The Cortex-M3 is able to handle external events or internal events in order to
wake-up the core (WFE). This is done by configuring the external lines WUP0-15 as fast startup
wake-up pins (refer to
can be used to wake up the CPU (exit from WFE).
Entering Wait mode:
Note:
The purpose of the sleep mode is to optimize the power consumption of the device versus the
response time. In this mode, only the core clock is stopped. The peripheral clocks can be
enabled. The current consumption in this mode is application dependent.
This mode is entered via Wait for Interrupt (WFI) or Wait for Event (WFE) instructions with
LPM = 0 in PMC_FSMR.
The processor can be awakened from an interrupt if WFI instruction of the Cortex M3 is used, or
from an event if WFE instruction is used to enter this mode.
• WKUPEN0-15 pins (level transition, configurable debouncing)
• Supply Monitor alarm
• RTC alarm
• RTT alarm
• Select the 4/8/12 MHz fast RC oscillator as Main Clock
• Set the LPM bit in the PMC Fast Startup Mode Register (PMC_FSMR)
• Execute the Wait-For-Event (WFE) instruction of the processor
Internal Main clock resynchronization cycles are necessary between the writing of MOSCRCEN
bit and the effective entry in Wait mode. Depending on the user application, Waiting for
MOSCRCEN bit to be cleared is recommended to ensure that the core will not execute undesired
instructions.
Section 5.7 “Fast
Startup”). RTC or RTT Alarm and USB wake-up events
SAM3S16
15