C8051F502-IMR Silicon Laboratories Inc, C8051F502-IMR Datasheet - Page 284

• Manufacturer Part Number: C8051F502-IMR
• Description: MCU 8-Bit C8051F50x 8051 CISC 64KB Flash 2.5V/3.3V/5V 32-Pin QFN EP T/R
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F502-IMR

• Package: 32QFN EP
• Device Core: 8051
• Family Name: C8051F50x
• Maximum Speed: 50 MHz
• Ram Size: 4.25 KB
• Program Memory Size: 64 KB
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/UART
• On-chip Adc: 32-chx12-bit
• Operating Temperature: -40 to 125 °C
• Number Of Timers: 4

C8051F50x/F51x
SFR Definition 26.13. TMR3CN: Timer 3 Control
SFR Address = 0x91; SFR Page = 0x00
284
Name
Reset
Bit
Type
7
6
5
4
3
2
1
0
Bit
T3SPLIT
TF3CEN
TF3LEN
T3XCLK
Unused
Name
TF3H
TF3L
TR3
TF3H
R/W
7
0
Timer 3 High Byte Overflow Flag.
Set by hardware when the Timer 3 high byte overflows from 0xFF to 0x00. In 16 bit
mode, this will occur when Timer 3 overflows from 0xFFFF to 0x0000. When the
Timer 3 interrupt is enabled, setting this bit causes the CPU to vector to the Timer 3
interrupt service routine. This bit is not automatically cleared by hardware.
Timer 3 Low Byte Overflow Flag.
Set by hardware when the Timer 3 low byte overflows from 0xFF to 0x00. TF3L will
be set when the low byte overflows regardless of the Timer 3 mode. This bit is not
automatically cleared by hardware.
Timer 3 Low Byte Interrupt Enable.
When set to 1, this bit enables Timer 3 Low Byte interrupts. If Timer 3 interrupts are
also enabled, an interrupt will be generated when the low byte of Timer 3 overflows.
Timer 3 Capture Mode Enable.
0: Timer 3 Capture Mode is disabled.
1: Timer 3 Capture Mode is enabled.
Timer 3 Split Mode Enable.
When this bit is set, Timer 3 operates as two 8-bit timers with auto-reload.
0: Timer 3 operates in 16-bit auto-reload mode.
1: Timer 3 operates as two 8-bit auto-reload timers.
Timer 3 Run Control.
Timer 3 is enabled by setting this bit to 1. In 8-bit mode, this bit enables/disables
TMR3H only; TMR3L is always enabled in split mode.
Read = 0b; Write = Don’t Care
Timer 3 External Clock Select.
This bit selects the external clock source for Timer 3. If Timer 3 is in 8-bit mode, this
bit selects the external oscillator clock source for both timer bytes. However, the
Timer 3 Clock Select bits (T3MH and T3ML in register CKCON) may still be used to
select between the external clock and the system clock for either timer.
0: Timer 3 clock is the system clock divided by 12.
1: Timer 3 clock is the external clock divided by 8 (synchronized with SYSCLK).
TF3L
R/W
6
0
TF3LEN
R/W
5
0
TF3CEN
R/W
Rev. 1.2
4
0
Function
T3SPLIT
R/W
3
0
TR3
R/W
2
0
R
1
0
T3XCLK
R/W
0
0