MC9S08GT16CFB Freescale Semiconductor, MC9S08GT16CFB Datasheet - Page 82

• Manufacturer Part Number: MC9S08GT16CFB
• Manufacturer: Freescale Semiconductor

Specifications of MC9S08GT16CFB

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: SCI/SPI
• Program Memory Type: Flash
• Program Memory Size: 16KB
• Total Internal Ram Size: 1KB
• # I/os (max): 36
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2.08V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Lead Free Status / Rohs Status: Not Compliant

Chapter 6 Parallel Input/Output
6.3.6
Port F is an 8-bit port general-purpose I/O that is not shared with any peripheral module. Port F has high
current output drivers.
Port F pins are available as general-purpose I/O pins controlled by the port F data (PTFD), data direction
(PTFDD), pullup enable (PTFPE), and slew rate control (PTFSE) registers. Refer to
I/O
6.3.7
Port G is an 8-bit port which is shared among the background/mode select function, oscillator, and
general-purpose I/O. When the background/mode select function or oscillator is enabled, the pin direction
will be controlled by the module function.
Port G pins are available as general-purpose I/O pins controlled by the port G data (PTGD), data direction
(PTGDD), pullup enable (PTGPE), and slew rate control (PTGSE) registers. Refer to
I/O
The internal pullup for PTG0 is enabled when the background/mode select function is enabled, regardless
of the state of PTGPE0. During reset, the BKGD/MS pin functions as a mode select pin. After the MCU
is out of reset, the BKGD/MS pin becomes the background communications input/output pin. The PTG0
can be configured to be a general-purpose output pin. Refer to
Chapter 5, “Resets, Interrupts, and System
more information about using this pin.
The ICG module can be configured to use PTG2–PTG1 ports as crystal oscillator or external clock pins.
Refer to
as oscillator pins.
6.4
Provided no on-chip peripheral is controlling a port pin, the pins operate as general-purpose I/O pins that
are accessed and controlled by a data register (PTxD), a data direction register (PTxDD), a pullup enable
register (PTxPE), and a slew rate control register (PTxSE) where x is A, B, C, D, E, F, or G.
82
Controls”
Controls”
Port G
Port F
Chapter 13, “Inter-Integrated Circuit (IIC)
Parallel I/O Controls
Port F and High-Current Drivers
Port G, BKGD/MS, and Oscillator
for more information about general-purpose I/O control.
for more information about general-purpose I/O control.
MCU Pin:
MCU Pin:
PTG7
PTF7
Bit 7
Bit 7
MC9S08GB/GT Data Sheet, Rev. 2.3
PTG6
PTF6
Figure 6-8. Port G Pin Names
Figure 6-7. Port F Pin Names
6
6
Configuration”, and
PTG5
PTF5
5
5
Module” for more information about using these pins
PTG4
PTF4
4
4
Chapter 3, “Modes of
Chapter 15, “Development
PTG3
PTF3
3
3
EXTAL
PTG2/
PTF2
2
2
PTG1/
XTAL
PTF1
Section 6.4, “Parallel
Section 6.4, “Parallel
Freescale Semiconductor
1
1
Operation”,
BKGD/MS
Support” for
PTG0/
PTF0
Bit 0
Bit 0