NT30-KBA04 Omron, NT30-KBA04 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
NT30-KBA04
Manufacturer Part Number
NT30-KBA04
Description
ANTI GLARE COVER FOR NT31
Manufacturer
Omron
Specifications of NT30-KBA04
Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 12 of 311
- Download datasheet (6Mb)
xiv
Safety Precautions
S Do not apply an AC power supply across the power supply terminals.
S Use a DC power supply with a low voltage fluctuation.
S When complying with EC low voltage directives use a power supply with rein-
S For the connection to the power supply terminal block, twisted-pair wires with a
S If the DIP switch settings have been changed while power was supplied to the
S Before switching ON the power for the first time, set pin 6 of DIP switch SW2 on
S Press the Abort touch switch on the PT when screen data transmission has
S Check the operation of screen data and ladder program thoroughly before ac-
S Press touch switches with a force of no greater than 30 N. Applying higher force
S Do not press touch switches carelessly while the backlight is OFF or while
S As far as possible, disconnect all devices connected to the output terminals be-
forced insulation.
2 mm
used. Tighten the screws on the terminal block to a torque of 0.8 N⋅cm. Other-
wise fire may occur.
PT, reset the power to the PT. The changes with the DIP switch become effec-
tive only after the power supply is reset.
the PT to ON (it is set to OFF on shipping). If it is left OFF, messages will not be
displayed normally.
been completed. Unless this touch switch is pressed, the screen data will not
be correctly registered. If the Abort touch switch is pressed during transmis-
sion, the screen data will not be correctly registered.
tually using them.
may cause glass to break, resulting in injuries or preventing operation.
nothing is displayed on the screen. The system may operate unpredictably.
Press touch switches only after confirming system safety.
fore executing the output check. Otherwise, each time an output terminal
comes ON during the check operation, the outputs to the devices may be acti-
vated.
2
or greater cross sectional area and M 3.5 size crimp terminals must be
3
Related parts for NT30-KBA04
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![NT30-KBA01](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
CHEMICAL RESISTANT COVER FOR NT31
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: