PIC18C801-I/L Microchip Technology, PIC18C801-I/L Datasheet - Page 173

• Manufacturer Part Number: PIC18C801-I/L
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LDCC,84PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C801-I/L

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 37
• Program Memory Type: ROMless
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 84-PLCC
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: 3-Wire, I2C, SPI, USART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 47
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DV164005, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164310 - MODULE SKT FOR PM3 84PLCCXLT84L1 - SOCKET TRANSITION ICE 84PLCCAC174012 - MODULE SKT PROMATEII 84PLCC
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C801-I/LR; PIC18C801-I/LR; PIC18C801I/L

15.4.16.1
During a START condition, a bus collision occurs if:
a)
b)
During a START condition, both the SDA and the SCL
pins are monitored.
If the SDA pin is already low, or the SCL pin is already
low, then all of the following occur:
• the START condition is aborted;
• the BCLIF flag is set, and
• the MSSP module is reset to its IDLE state
The START condition begins with the SDA and SCL
pins de-asserted. When the SDA pin is sampled high,
the baud rate generator is loaded from SSPADD<6:0>
and counts down to 0. If the SCL pin is sampled low
while SDA is high, a bus collision occurs, because it is
assumed that another master is attempting to drive a
data '1' during the START condition.
FIGURE 15-21:
(Figure 15-21).
2001 Microchip Technology Inc.
SDA
SCL
SEN
BCLIF
S
SSPIF
SDA or SCL are sampled low at the beginning of
the START condition (Figure 15-21).
SCL is sampled low before SDA is asserted low
(Figure 15-22).
Bus Collision During a START
Condition
BUS COLLISION DURING START CONDITION (SDA ONLY)
condition if SDA = 1, SCL=1
Set SEN, enable START
SDA sampled low before
START condition.
S bit and SSPIF set because
SDA = 0, SCL = 1.
. Set BCLIF,
SDA goes low before the SEN bit is set.
S bit and SSPIF set because
SDA = 0, SCL = 1.
Advance Information
Set BCLIF.
SSPIF and BCLIF are
cleared in software.
If the SDA pin is sampled low during this count, the
BRG is reset and the SDA line is asserted early
(Figure 15-23). If, however, a '1' is sampled on the SDA
pin, the SDA pin is asserted low at the end of the BRG
count. The baud rate generator is then reloaded and
counts down to 0, and during this time, if the SCL pin is
sampled as '0', a bus collision does not occur. At the
end of the BRG count, the SCL pin is asserted low.
Note:
SEN cleared automatically because of bus collision.
SSP module reset into IDLE state.
The reason that bus collision is not a factor
during a START condition, is that no two
bus masters can assert a START condition
at the exact same time. Therefore, one
master will always assert SDA before the
other. This condition does not cause a bus
collision, because the two masters must be
allowed to arbitrate the first address follow-
ing the START condition. If the address is
the same, arbitration must be allowed to
continue into the data portion, Repeated
START or STOP conditions.
PIC18C601/801
SSPIF and BCLIF are
cleared in software.
DS39541A-page 173