ATA5771-DK1 Atmel, ATA5771-DK1 Datasheet - Page 51
ATA5771-DK1
Manufacturer Part Number
ATA5771-DK1
Description
BOARD XMITTER FOR ATA5771 868MHZ
Manufacturer
Atmel
Type
Transmitterr
Specifications of ATA5771-DK1
Frequency
868MHz
Maximum Frequency
868 MHz
Supply Voltage (max)
4 V
Supply Voltage (min)
2 V
Supply Current
8.5 mA
Product
RF Development Tools
For Use With/related Products
ATA5771
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 51 of 219
- Download datasheet (4Mb)
4.11.4.2
4.11.5
4.11.5.1
9137E–RKE–12/10
Register Description
Safety Level 2
MCUSR – MCU Status Register
1. In the same operation, write a logic one to WDCE and WDE. A logic one must be writ-
2. Within the next four clock cycles, in the same operation, write the WDE and WDP bits
In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read as one.
A timed sequence is needed when changing the Watchdog Time-out period. To change the
Watchdog Time-out, the following procedure must be followed:
1. In the same operation, write a logical one to WDCE and WDE. Even though the WDE
2. Within the next four clock cycles, in the same operation, write the WDP bits as desired,
The MCU Status Register provides information on which reset source caused an MCU Reset.
• Bits 7..4 – Res: Reserved Bits
These bits are reserved bits in the ATtiny44V and will always read as zero.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a Watchdog Reset occurs. The bit is reset by a Power-on Reset, or by writing
a logic zero to the flag.
• Bit 2 – BORF: Brown-out Reset Flag
This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writing
a logic zero to the flag.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the
flag.
To make use of the Reset Flags to identify a reset condition, the user should read and then
reset the MCUSR as early as possible in the program. If the register is cleared before another
reset occurs, the source of the reset can be found by examining the Reset Flags.
Bit
0x34 (0x54)
Read/Write
Initial Value
ten to WDE regardless of the previous value of the WDE bit.
as desired, but with the WDCE bit cleared.
always is set, the WDE must be written to one to start the timed sequence.
but with the WDCE bit cleared. The value written to the WDE bit is irrelevant.
R
7
–
0
R
6
–
0
R
5
–
0
R
4
–
0
WDRF
R/W
Atmel ATA5771/73/74
3
BORF
See Bit Description
R/W
2
EXTRF
R/W
1
PORF
R/W
0
MCUSR
51
Related parts for ATA5771-DK1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
XMITTR UHF ASK/FSK 868MHZ 24VQFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: