ATA5771-DK1 Atmel, ATA5771-DK1 Datasheet - Page 27
ATA5771-DK1
Manufacturer Part Number
ATA5771-DK1
Description
BOARD XMITTER FOR ATA5771 868MHZ
Manufacturer
Atmel
Type
Transmitterr
Specifications of ATA5771-DK1
Frequency
868MHz
Maximum Frequency
868 MHz
Supply Voltage (max)
4 V
Supply Voltage (min)
2 V
Supply Current
8.5 mA
Product
RF Development Tools
For Use With/related Products
ATA5771
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 27 of 219
- Download datasheet (4Mb)
4.8.3.6
9137E–RKE–12/10
Preventing EEPROM Corruption
The next code examples show assembly and C functions for reading the EEPROM. The
examples assume that interrupts are controlled so that no interrupts will occur during execu-
tion of these functions.
Note:
During periods of low V
too low for the CPU and the EEPROM to operate properly. These issues are the same as for
board level systems using EEPROM, and the same design solutions should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too low.
First, a regular write sequence to the EEPROM requires a minimum voltage to operate cor-
rectly. Secondly, the CPU itself can execute instructions incorrectly, if the supply voltage is too
low.
EEPROM data corruption can easily be avoided by following this design recommendation:
Keep the Atmel
age. This can be done by enabling the internal Brown-out Detector (BOD). If the detection
level of the internal BOD does not match the needed detection level, an external low V
protection circuit can be used. If a reset occurs while a write operation is in progress, the write
operation will be completed provided that the power supply voltage is sufficient.
Assembly Code Example
C Code Example
EEPROM_read:
unsigned char EEPROM_read(unsigned char ucAddress)
{
}
; Wait for completion of previous write
sbic EECR,EEPE
rjmp EEPROM_read
; Set up address (r17) in address register
out EEARL, r17
; Start eeprom read by writing EERE
sbi EECR,EERE
; Read data from data register
in
ret
/* Wait for completion of previous write */
while(EECR & (1<<EEPE))
/* Set up address register */
EEARL = ucAddress;
/* Start eeprom read by writing EERE */
EECR |= (1<<EERE);
/* Return data from data register */
return EEDR;
The code examples are only valid for the Atmel ATtiny44V, using 8-bit addressing mode.
;
r16,EEDR
®
AVR
®
CC
RESET active (low) during periods of insufficient power supply volt-
, the EEPROM data can be corrupted because the supply voltage is
Atmel ATA5771/73/74
CC
reset
27
Related parts for ATA5771-DK1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
XMITTR UHF ASK/FSK 868MHZ 24VQFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: