ATA5771-DK1 Atmel, ATA5771-DK1 Datasheet - Page 178

• Manufacturer Part Number: ATA5771-DK1
• Description: BOARD XMITTER FOR ATA5771 868MHZ
• Manufacturer: Atmel
• Type: Transmitterr

Specifications of ATA5771-DK1

• Frequency: 868MHz
• Maximum Frequency: 868 MHz
• Supply Voltage (max): 4 V
• Supply Voltage (min): 2 V
• Supply Current: 8.5 mA
• Product: RF Development Tools
• For Use With/related Products: ATA5771
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 4-70.
178
Instruction
Chip Erase
Load “Write
Flash”
Command
Load Flash Page
Buffer
Load Flash High
Address and
Program Page
Load “Read
Flash”
Command
Read Flash Low
and High Bytes
Load “Write
EEPROM”
Command
Load EEPROM
Page Buffer
Note:
Notes:
a = address high bits, b = address low bits, d = data in high bits, e = data in low bits, p = data out high bits, q = data out low bits,
x = don’t care, 1 = Lock Bit1, 2 = Lock Bit2, 3 = CKSEL0 Fuse, 4 = CKSEL1 Fuse, 5 = CKSEL2 Fuse, 6 = CKSEL3 Fuse, 7 =
SUT0 Fuse, 8 = SUT1 Fuse, 9 = CKDIV8 Fuse, A = CKOUT Fuse, B = BODLEVEL0 Fuse, C = BODLEVEL1 Fuse, D=
BODLEVEL2 Fuse, E = EESAVE Fuse, F = WDTON Fuse, G = SPIEN Fuse, H = DWEN Fuse, I = RSTDISBL Fuse
1. For page sizes less than 256 words, parts of the address (bbbb_bbbb) will be parts of the page address.
2. For page sizes less than 256 bytes, parts of the address (bbbb_bbbb) will be parts of the page address.
3. The EEPROM is written page-wise. But only the bytes that are loaded into the page are actually written to the EEPROM.
Atmel ATA5771/73/74
Page-wise EEPROM access is more efficient when multiple bytes are to be written to the same page. Note that auto-erase
of EEPROM is not available in High-voltage Serial Programming, only in SPI Programming.
High-voltage Serial Programming Instruction Set for Atmel
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
0_1000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0001_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_ bbbb_bbbb _00
0_0000_1100_00
x_xxxx_xxxx_xx
0_dddd_dddd_00
0_0011_1100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0010_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1000_00
x_xxxx_xxxx_xx
0_0001_0001_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Instr.1/5
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1101_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
p_pppp_pppx_xx
0_aaaa_aaaa_00
0_0001_1100_00
x_xxxx_xxxx_xx
Instr.2/6
Instruction Format
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
Instr.3/7
®
ATtiny44V
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
q_qqqq_qqqx_xx
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
Instr.4
Operation Remarks
Wait after Instr.3 until SDO goes
high for the Chip Erase cycle to
finish.
Enter Flash Programming code.
Repeat after Instr. 1 - 7until the
entire page buffer is filled or until
all data within the page is filled.
See Note 1.
Wait after Instr 3 until SDO goes
high. Repeat Instr. 2 - 3 for each
loaded Flash Page until the entire
Flash or all data is programmed.
Repeat Instr. 1 for a new 256 byte
page. See Note 1.
Enter Flash Read mode.
Repeat Instr. 1, 3 - 6 for each new
address. Repeat Instr. 2 for a new
256 byte page.
Instr 5 - 6.
Enter EEPROM Programming
mode.
Repeat Instr. 1 - 5 until the entire
page buffer is filled or until all data
within the page is filled. See Note
2.
Instr 5-7.
9137E–RKE–12/10