C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 28

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

C8051F320/1
1.10. Comparators
C8051F320/1 devices include two on-chip voltage comparators that are enabled/disabled and configured via user
software. Port I/O pins may be configured as comparator inputs via a selection mux. Two comparator outputs may be
routed to a Port pin if desired: a latched output and/or an unlatched (asynchronous) output. Comparator response time
is programmable, allowing the user to select between high-speed and low-power modes. Positive and negative hyster-
esis are also configurable.
Comparator interrupts may be generated on rising, falling, or both edges. When in IDLE mode, these interrupts may
be used as a “wake-up” source. Comparator0 may also be configured as a reset source. Figure 1.11 shows the
Comparator0 block diagram.
28
CMX0N1
CMX0N0
CMX0P1
CMX0P0
Note: P2.4 and P2.5 available
only on C8051F320
P1.0
P1.4
P2.0
P2.4
P1.1
P1.5
P2.1
P2.5
CP0HYP1
CP0HYP0
CP0HYN1
CP0HYN0
Figure 1.11. Comparator0 Block Diagram
CP0OUT
CP0RIF
CP0FIF
CP0EN
CP0 +
CP0 -
CP0MD1
CP0MD0
CP0RIE
CP0FIE
Rev. 1.1
+
-
GND
VDD
Decision
Reset
Tree
(SYNCHRONIZER)
D
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Rising-edge
CP0
Crossbar
Interrupt
Logic
Falling-edge
Interrupt
CP0
CP0A
CP0
CP0
CP0RIE
CP0FIE