C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 171

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
CLRDT
Figure 15.24. EOUTCSRL: USB0 OUT Endpoint Control High Byte (USB Register)
Bit7
W
CLRDT: Clear Data Toggle
Write: Software should write ‘1’ to this bit to reset the OUT endpoint data toggle to ‘0’.
Read: This bit always reads ‘0’.
STSTL: Sent Stall
Hardware sets this bit to ‘1’ when a STALL handshake signal is transmitted. This flag must be cleared
by software.
SDSTL: Send Stall
Software should write ‘1’ to this bit to generate a STALL handshake. Software should write ‘0’ to this
bit to terminate the STALL signal. This bit has no effect in ISO mode.
FLUSH: FIFO Flush
Writing a ‘1’ to this bit flushes the next packet to be read from the OUT endpoint FIFO. The FIFO
pointer is reset and the OPRDY bit is cleared. If the FIFO contains multiple packets, software must
write ‘1’ to FLUSH for each packet. Hardware resets the FLUSH bit to ‘0’ when the FIFO flush is
complete.
DATERR: Data Error
In ISO mode, this bit is set by hardware if a received packet has a CRC or bit-stuffing error. It is
cleared when software clears OPRDY. This bit is only valid in ISO mode.
OVRUN: Data Overrun
This bit is set by hardware when an incoming data packet cannot be loaded into the OUT endpoint
FIFO. This bit is only valid in ISO mode, and must be cleared by software.
0: No data overrun.
1: A data packet was lost because of a full FIFO since this flag was last cleared.
FIFOFUL: OUT FIFO Full
This bit indicates the contents of the OUT FIFO. If double buffering is enabled for the endpoint
(DBIEN = ‘1’), the FIFO is full when the FIFO contains two packets. If DBIEN = ‘0’, the FIFO is full
when the FIFO contains one packet.
0: OUT endpoint FIFO is not full.
1: OUT endpoint FIFO is full.
OPRDY: OUT Packet Ready
Hardware sets this bit to ‘1’ and generates an interrupt when a data packet is available. Software
should clear this bit after each data packet is unloaded from the OUT endpoint FIFO.
STSTL
R/W
Bit6
SDSTL
R/W
Bit5
FLUSH
Bit4
W
DATERR
Bit3
R
Rev. 1.1
OVRUN
R/W
Bit2
FIFOFUL
Bit1
R
C8051F320/1
OPRDY
R/W
Bit0
USB Address:
00000000
Reset Value
0x14
171