C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 197

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

17.3. Multiprocessor Communications
9-Bit UART mode supports multiprocessor communication between a master processor and one or more slave pro-
cessors by special use of the ninth data bit. When a master processor wants to transmit to one or more slaves, it first
sends an address byte to select the target(s). An address byte differs from a data byte in that its ninth bit is logic 1; in
a data byte, the ninth bit is always set to logic 0.
Setting the MCE0 bit (SCON0.5) of a slave processor configures its UART such that when a stop bit is received, the
UART will generate an interrupt only if the ninth bit is logic 1 (RB80 = 1) signifying an address byte has been
received. In the UART interrupt handler, software will compare the received address with the slave's own assigned 8-
bit address. If the addresses match, the slave will clear its MCE0 bit to enable interrupts on the reception of the fol-
lowing data byte(s). Slaves that weren't addressed leave their MCE0 bits set and do not generate interrupts on the
reception of the following data bytes, thereby ignoring the data. Once the entire message is received, the addressed
slave resets its MCE0 bit to ignore all transmissions until it receives the next address byte.
Multiple addresses can be assigned to a single slave and/or a single address can be assigned to multiple slaves,
thereby enabling "broadcast" transmissions to more than one slave simultaneously. The master processor can be con-
figured to receive all transmissions or a protocol can be implemented such that the master/slave role is temporarily
reversed to enable half-duplex transmission between the original master and slave(s).
RX
Master
Device
Figure 17.6. UART Multi-Processor Mode Interconnect Diagram
TX
RX
Device
Slave
TX
RX
Device
Slave
Rev. 1.1
TX
RX
Device
Slave
C8051F320/1
TX
V+
197