AT91RM9200-QU-002 Atmel, AT91RM9200-QU-002 Datasheet - Page 248

• Manufacturer Part Number: AT91RM9200-QU-002
• Description: IC ARM9 MCU 208 PQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91RM9200-QU-002

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: POR
• Number Of I /o: 122
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-MQFP, 208-PQFP
• Processor Series: AT91Rx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, UART, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 122
• Number Of Timers: 10 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91RM9200-EK
• Minimum Operating Temperature: - 40 C
• Eeprom Memory: 0 Bytes
• Input Output: 122
• Interface: EBI/EMI, UART/USART
• Ios: 122
• Memory Type: ROM
• Number Of Bits: 32
• Package Type: 208-pin PQFP
• Programmable Memory: 128K Bytes
• Timers: 3-16-bit
• Voltage, Range: 1.65-1.95 V
• Cpu Family: 91R
• Device Core: ARM920T
• Device Core Size: 32b
• Frequency (max): 180MHz
• Total Internal Ram Size: 16KB
• # I/os (max): 122
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 208
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

22.7.4
22.7.4.1
22.7.4.2
22.7.4.3
22.7.4.4
248
AT91RM9200
Fast Interrupt
Fast Interrupt Source
Fast Interrupt Control
Fast Interrupt Vectoring
Fast Interrupt Handlers
Note:
The interrupt source 0 is the only source which can raise a fast interrupt request to the proces-
sor. The interrupt source 0 is generally connected to an FIQ pin of the product, either directly or
through a PIO Controller.
The fast interrupt logic of the AIC has no priority controller. The mode of interrupt source 0 is
programmed with the AIC_SMR0 and the field PRIOR of this register is not used even if it reads
what has been written. The field SRCTYPE of AIC_SMR0 enables programming the fast inter-
rupt source to be positive-edge triggered or negative-edge triggered or high-level sensitive or
low-level sensitive
Writing 0x1 in the AIC_IECR (Interrupt Enable Command Register) and AIC_IDCR (Interrupt
Disable Command Register) respectively enables and disables the fast interrupt. The bit 0 of
AIC_IMR (Interrupt Mask Register) indicates whether the fast interrupt is enabled or disabled.
The fast interrupt handler address can be stored in AIC_SVR0 (Source Vector Register 0). The
value written into this register is returned when the processor reads AIC_FVR (Fast Vector Reg-
ister). This offers a way to branch in one single instruction to the interrupt handler, as AIC_FVR
is mapped at the absolute address 0xFFFF F104 and thus accessible from the ARM fast inter-
rupt vector at address 0x0000 001C through the following instruction:
When the processor executes this instruction it loads the value read in AIC_FVR in its program
counter, thus branching the execution on the fast interrupt handler. It also automatically per-
forms the clear of the fast interrupt source if it is programmed in edge-triggered mode.
This section gives an overview of the fast interrupt handling sequence when using the AIC. It is
assumed that the programmer understands the architecture of the ARM processor, and espe-
cially the processor interrupt modes and associated status bits.
Assuming that:
When nFIQ is asserted if the bit “F” of CPSR is 0, the sequence is:
1. The Advanced Interrupt Controller has been programmed, AIC_SVR0 is loaded with
2. The Instruction at address 0x1C (FIQ exception vector address) is required to vector
3. The user does not need nested fast interrupts.
1. The CPSR is stored in SPSR_fiq, the current value of the program counter is loaded in
LDR
LDR PC, [PC, # -&F20]
the fast interrupt service routine address, and the interrupt source 0 is enabled.
the fast interrupt:
the FIQ link register (R14_FIQ) and the program counter (R15) is loaded with 0x1C. In
The “I” bit in SPSR is significant. If it is set, it indicates that the ARM core was on the verge of
masking an interrupt when the mask instruction was interrupted. Hence, when SPSR is restored,
the mask instruction is completed (interrupt is masked).
PC,[PC,# -&F20]
1768I–ATARM–09-Jul-09