C8051F930DK Silicon Laboratories Inc, C8051F930DK Datasheet - Page 288

• Manufacturer Part Number: C8051F930DK
• Description: KIT DEV C8051F920,F921,F930,F931
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F930DK

• Contents: Target Board, Power Adapter, USB Debug Adapter, Cables, Batteries, and Software
• Processor To Be Evaluated: C8051F930
• Processor Series: C8051F9xx
• Data Bus Width: 8 bit
• Interface Type: I2C, UART, SPI
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 0.9 V to 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: C8051F920, F921, F930, F931
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1473

C8051F93x-C8051F92x
25.2. Timer 2
Timer 2 is a 16-bit timer formed by two 8-bit SFRs: TMR2L (low byte) and TMR2H (high byte). Timer 2 may
operate in 16-bit auto-reload mode or (split) 8-bit auto-reload mode. The T2SPLIT bit (TMR2CN.3) defines
the Timer 2 operation mode. Timer 2 can also be used in Capture Mode to measure the SmaRTClock or
the Comparator 0 period with respect to another oscillator. The ability to measure the Comparator 0 period
with respect to the system clock is makes using Touch Sense Switches very easy.
Timer 2 may be clocked by the system clock, the system clock divided by 12, SmaRTClock divided by 8, or
Comparator 0 output. Note that the SmaRTClock divided by 8 and Comparator 0 output is synchronized
with the system clock.
25.2.1. 16-bit Timer with Auto-Reload
When T2SPLIT (TMR2CN.3) is zero, Timer 2 operates as a 16-bit timer with auto-reload. Timer 2 can be
clocked by SYSCLK, SYSCLK divided by 12, SmaRTClock divided by 8, or Comparator 0 output. As the
16-bit timer register increments and overflows from 0xFFFF to 0x0000, the 16-bit value in the Timer 2
reload registers (TMR2RLH and TMR2RLL) is loaded into the Timer 2 register as shown in Figure 25.4,
and the Timer 2 High Byte Overflow Flag (TMR2CN.7) is set. If Timer 2 interrupts are enabled (if IE.5 is
set), an interrupt will be generated on each Timer 2 overflow. Additionally, if Timer 2 interrupts are enabled
and the TF2LEN bit is set (TMR2CN.5), an interrupt will be generated each time the lower 8 bits (TMR2L)
overflow from 0xFF to 0x00.
288
SmaRTClock / 8
Comparator 0
SYSCLK / 12
T2XCLK[1:0]
00
01
11
SYSCLK
Figure 25.4. Timer 2 16-Bit Mode Block Diagram
M
H
T
3
M
T
3
L
CKCON
M
T
H
2
T
M
0
1
2
L
M
T
1
M
T
0
S
C
A
1
S
C
A
0
TR2
TCLK
Rev. 1.1
Overflow
TL2
TMR2RLL TMR2RLH
TMR2L
To SMBus
TMR2H
Reload
To ADC,
SMBus
TF2CEN
T2SPLIT
TF2LEN
T2XCLK
TF2H
TF2L
TR2
Interrupt