TMP86C909XB Toshiba, TMP86C909XB Datasheet - Page 179

• Manufacturer Part Number: TMP86C909XB
• Description: EMULATION CHIP FOR TMP86F SDIP
• Manufacturer: Toshiba

Specifications of TMP86C909XB

• Accessory Type: Adapter
• For Use With/related Products: TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.9 Intel Hex Format (Binary)
15.9 Intel Hex Format (Binary)
15.10Passwords
Table 15-16 Password Setting in the Blank Product and Non-Blank Product
TMP86F409NG compares the data string specified to the password with the password string transmitted from the
external controller. The area in which passwords can be specified is located at addresses F000H to FF9FH. The area
from FFA0H to FFFFH can not be specified as the passwords area.
product is considered as a blank product. Even in this case, the password count storage addresses and password
comparison start address must be specified. Table 15-16 shows the password setting in the blank product and non-
blank product.
The consecutive eight or more-byte data in the flash memory area can be specified to the password.
If addresses from FFE0H through FFFFH are filled with “FFH”, the passwords are not compared because the
Note 1: When addresses from FFE0H through FFFFH are filled with “FFH”, the product is recognized as a blank product.
Note 2: The data including the same consecutive data (three or more bytes) can not be used as a password. (This causes a pass-
Note 3: *: Don’t care.
Note 4: When the above condition is not met, a password error occurs. If a password error occurs, the device enters the halt con-
Note 5: In the flash memory writing mode or RAM loader mode, the blank product receives the Intel Hex format data immediately
Note 6: In the flash memory erasing mode, the external controller must not transmit the password string for the blank product.
(Password comparison start address)
(Password count storage address)
1. After receiving the checksum of a data record, the device waits for the start mark (3AH “:”) of the next data
2. After transmitting the checksum of end record, the external controller must transmit nothing, and wait for
3. If a receiving error or Intel Hex format error occurs, the device enters the halt condition without returning
record. After receiving the checksum of a data record, the device ignores the data except 3AH transmitted
by the external controller.
the 2-byte receive data (upper and lower bytes of the checksum).
an error code to the external controller. The Intel Hex format error occurs in the following case:
word error data. TMP86F409NG transmits no data and enters the halt condition.)
dition without returning the error code.
after receiving PCSA without receiving password strings. In this case, the subsequent processing is performed correctly
because the blank product ignores the data except the start mark (3AH “:”) as the Intel Hex format data, even if the exter-
nal controller transmits the dummy password string. However, if the dummy password string contains “3AH”, it is detected
as the start mark erroneously. The microcontroller enters the halt mode. If this causes the problem, do not transmit the
dummy password strings.
Password string setting
(Password count)
extended address of 1000H or larger.
When the record type is not 00H, 01H, or 02H
When a checksum error occurs
When the data length of an extended record (record type = 02H) is not 02H
When the device receives the data record after receiving an extended record (record type = 02H) with
When the data length of the end record (record type = 01H) is not 00H
Password
PNSA
PCSA
N
F000H ≤ PNSA ≤ FF9FH
F000H ≤ PCSA ≤ FF9FH
Blank Product (Note 1)
Not required (Note 5)
Page 168
*
F000H ≤ PCSA ≤ FFA0 - N
F000H ≤ PNSA ≤ FF9FH
Non-Blank Product
Required (Note 2)
8 ≤ N
TMP86F409NG