S912XEG128J2MAL Freescale Semiconductor, S912XEG128J2MAL Datasheet - Page 520

• Manufacturer Part Number: S912XEG128J2MAL
• Description: 16-bit Microcontrollers - MCU 16BIT 128K FLASH 16K RAM
• Manufacturer: Freescale Semiconductor

Specifications of S912XEG128J2MAL

• Rohs: yes
• Core: RISC
• Processor Series: HCS12X
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 128 KB
• Data Ram Size: 12 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-112
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 8
• Data Rom Size: 4 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• On-chip Dac: Yes
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 3.13 V

Chapter 13 Analog-to-Digital Converter (ADC12B16CV1)
13.3.2.9
This read-only register contains the Conversion Complete Flags CCF[15:0].
Read: Anytime
Write: Anytime, no effect
520
Module Base + 0x000A
CCF[15:0]
Reset
Field
15–0
W
R
15
0
Conversion Complete Flag n (n= 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) — A conversion complete
flag is set at the end of each conversion in a sequence. The flags are associated with the conversion position in
a sequence (and also the result register number). Therefore in non-fifo mode, CCF[8] is set when the ninth
conversion in a sequence is complete and the result is available in result register ATDDR8; CCF[9] is set when
the tenth conversion in a sequence is complete and the result is available in ATDDR9, and so forth.
If automatic compare of conversion results is enabled (CMPE[n]=1 in ATDCMPE), the conversion complete flag
is only set if comparison with ATDDRn is true and if ACMPIE=1 a compare interrupt will be requested. In this
case, as the ATDDRn result register is used to hold the compare value, the result will not be stored there at the
end of the conversion but is lost.
In case of a concurrent set and clear on CCF[n]: The clearing by method A) will overwrite the set. The clearing
by methods B) or C) or D) will be overwritten by the set.
0 Conversion number n not completed or successfully compared
1 If (CMPE[n]=0): Conversion number n has completed. Result is ready in ATDDRn.
ATD Status Register 2 (ATDSTAT2)
= Unimplemented or Reserved
If (CMPE[n]=1): Compare for conversion result number n with compare value in ATDDRn, using compare
operator CMPGT[n] is true. (No result available in ATDDRn)
A flag CCF[n] is cleared when one of the following occurs:
A) Write to ATDCTL5 (a new conversion sequence is started)
B) If AFFC=0, write “1” to CCF[n]
C) If AFFC=1 and CMPE[n]=0, read of result register ATDDRn
D) If AFFC=1 and CMPE[n]=1, write to result register ATDDRn
14
0
13
0
12
Figure 13-11. ATD Status Register 2 (ATDSTAT2)
0
MC9S12XE-Family Reference Manual Rev. 1.25
Table 13-19. ATDSTAT2 Field Descriptions
11
0
10
0
0
9
CCF[15:0]
0
8
Description
0
7
0
6
0
5
4
0
0
3
Freescale Semiconductor
0
2
0
1
0
0