S912XEG128J2MAL Freescale Semiconductor, S912XEG128J2MAL Datasheet - Page 274

• Manufacturer Part Number: S912XEG128J2MAL
• Description: 16-bit Microcontrollers - MCU 16BIT 128K FLASH 16K RAM
• Manufacturer: Freescale Semiconductor

Specifications of S912XEG128J2MAL

• Rohs: yes
• Core: RISC
• Processor Series: HCS12X
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 128 KB
• Data Ram Size: 12 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-112
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 8
• Data Rom Size: 4 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• On-chip Dac: Yes
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 3.13 V

Chapter 6 Interrupt (S12XINTV2)
6.4.5
The XINT module supports three system reset exception request types (for details please refer to the Clock
and Reset Generator module (CRG)):
6.4.6
The priority (from highest to lowest) and address of all exception vectors issued by the XINT module upon
request by the CPU is shown in
than maskable interrupts. Please note that between the three software interrupts (Unimplemented op-code
trap request, SWI/BGND request, SYS request) there is no real priority defined because they cannot occur
simultaneously (the S12XCPU executes one instruction at a time).
1. 16 bits vector address based
2. only implemented if device features both a Memory Protection Unit (MPU) and an XGATE co-processor
3. only implemented if device features a Memory Protection Unit (MPU)
274
1. Pin reset, power-on reset, low-voltage reset, or illegal address reset
2. Clock monitor reset request
3. COP watchdog reset request
(Vector base + 0x00F8)
(Vector base + 0x00F6)
(Vector base + 0x0012)
(Vector base + 0x0018)
(Vector base + 0x0016)
(Vector base + 0x0014)
(Vector base + 0x00F4)
(Vector base + 0x00F2)
(Vector base + 0x0010)
Vector Address
0x00F0–0x001A)
(Vector base +
0xFFFC
0xFFFE
0xFFFA
Reset Exception Requests
Exception Priority
Care must be taken to ensure that all exception requests remain active until
the system begins execution of the applicable service routine; otherwise, the
exception request may not get processed at all or the result may be a
spurious interrupt request (vector at address (vector base + 0x0010)).
(1)
Pin reset, power-on reset, low-voltage reset, illegal address reset
Clock monitor reset
COP watchdog reset
Unimplemented op-code trap
Software interrupt instruction (SWI) or BDM vector request
System call interrupt instruction (SYS)
(reserved for future use)
XGATE Access violation interrupt request
CPU Access violation interrupt request
XIRQ interrupt request
IRQ interrupt request
Device specific I bit maskable interrupt sources (priority determined by the associated
configuration registers, in descending order)
Spurious interrupt
Table 6-10. Exception Vector Map and Priority
MC9S12XE-Family Reference Manual Rev. 1.25
Table
6-10. Generally, all non-maskable interrupts have higher priorities
NOTE
(3)
(2)
Source
Freescale Semiconductor