ATUC64L4U Atmel Corporation, ATUC64L4U Datasheet - Page 88

• Manufacturer Part Number: ATUC64L4U
• Manufacturer: Atmel Corporation

Specifications of ATUC64L4U

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

9.1.2.2
32002F–03/2010
Accessing the debug features
(such as reading the register file) may require running sections of debug code on the CPU,
which can also be handled in this level. The emulator translates the communication from the
host into commands transmitted to the target over the JTAG port. If trace is enabled, trace mes-
sages are transmitted from the device on the Nexus-defined auxiliary (AUX) port. The AUX port
can be scaled to the number of output pins needed to sustain the estimated bandwidth require-
ment. The Nexus protocol defines the format of the messages and signals, the pin count options
and pinout of the debug port, and the type of connector used.
Figure 9-1.
A number of blocks handle the various debug functions specified by the Nexus standard. The
emulator communicates with registers in these blocks by commands on the JTAG port, as spec-
ified by the Nexus standard. OCD registers are typically used for configuration, control, and
status information. Trace information and debug events can also generate messages to be
transmitted on the AUX port.
Registers are indexed and are accessed through Read Register and Write Register messages
from the emulator. Alternatively, they can be accessed by the CPU through mtdr and mfdr
instructions, which gives a debug monitor in the CPU access to most of the debug features in
the OCD system, as described in
Service Access Bus (SAB)
Debug
inst
Service Access
Port (SAP)
Control
Flow
Block diagram of the OCD system (shaded) and its main connections.
TAP
Unit
control
signals
OCD
CPU
JTAG Port
Status msg
Debug
Emulator
W atchpoint
“OCD Register Access” on page
Breakpoint Unit
msg
AUX Port
Trigger
Trigger
observation
signals
CPU
Transmit Queue
CPU observation units
Data Trace
Comparators
Comparators
Program
Trace
Data
PC
Host
Trace msg
Data
Message
Branch
Trace
Ownership
Ownership
Message
Trace
Trace
Unit
98.
AVR32
OCD system
88