CV500BC101 Omron, CV500BC101 Datasheet - Page 60
CV500BC101
Manufacturer Part Number
CV500BC101
Description
Programmable Logic Controller
Manufacturer
Omron
Datasheet
1.CV500BC031.pdf
(403 pages)
Specifications of CV500BC101
Peak Reflow Compatible (260 C)
No
Leaded Process Compatible
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 60 of 403
- Download datasheet (5Mb)
Data Links Procedures
6. Set the data link mode.
7. Register the data link tables by making the following settings for each
Note a) When using fewer than 33 nodes, make sure that the Wired Net-
node.
First data link status word
Data link nodes
Area
1
Area
2
Note Offsets are used to control where data is placed within the receive
Enable 62 nodes for a
wired network.
Set data link mode to
manual.
Set the data link status
storage format. (CS/
CJ Series only)
b) Only node addresses 1 through 32 can be used on networks for
c) Be sure that the data link mode in the data link parameters in the
d) When using the 8-bit storage format, make sure that the relevant
area.
Contents
First data link sta-
tus words
Numbers of data
link words
Data link offsets
First data link sta-
tus words
Numbers of data
link words
Data link offsets
Contents
work 62 Node Enable Bit if the DM Parameter Area software
switch is turned OFF to restrict the network to 32 nodes maximum.
To construct a network that uses a node address higher than 32,
all nodes must use the CS1W-CLK21-V1, CS1W-CLK23, CJ1W-
CLK21-V1, or CJ1W-CLK23.
which 62 nodes have not been enabled.
DM Area is set to 00 when using manually set data links.
locations in the DM Parameter Area are set to 0. The storage for-
mat used by all models other than CS1W-CLK21-V1, CS1W-
CLK23, CJ1W-CLK21-V1, and CJ1W-CLK23 is fixed at 8-bit, re-
gardless of the setting.
Use Support Soft-
ware for the PLC or
the Programming
Console.
Use Support Soft-
ware for the PLC or
the Programming
Console. (See note b.)
Use Support Soft-
ware for the PLC or
the Programming
Console.
Use the Controller
Link Support Soft-
ware or CX-Pro-
grammer.
Method
Method
All nodes
Note: This setting
must be made to con-
struct a network that
uses a node address
higher than 32 (See
note a.)
Data link startup node
only
The node that is used
to start the data links
is called the startup
node. It is necessary
to decide beforehand
which node will be the
startup node.
Data link startup node
only (See note c.)
All nodes within the
network
Delete from the data
link tables all nodes
that are not in a data
link.
Nodes
Nodes
Section 2-1
80
115
162
117
Page
Page
35
Related parts for CV500BC101
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: