SAK-C167CS-L40M CA+ Infineon Technologies, SAK-C167CS-L40M CA+ Datasheet - Page 38

• Manufacturer Part Number: SAK-C167CS-L40M CA+
• Description: IC MCU 16BIT 40MHZ MQFP-144
• Manufacturer: Infineon Technologies
• Series: C16xxr

Specifications of SAK-C167CS-L40M CA+

• Core Processor: C166
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, SPI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Type: ROMless
• Ram Size: 11K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144- BSQFP
• Data Bus Width: 16 bit
• Data Ram Size: 11 KB
• Interface Type: 1xUSART, 1xSSC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 9
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Packages: PG-MQFP-144
• Max Clock Frequency: 40.0 MHz
• Sram (incl. Cache): 11.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 24
• Program Memory: 0.0 KByte
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: K167CSL40MCAZNP; K167CSL40MCAZXP; SAK-C167CS-L40M CA+; SAK-C167CS-L40MCAIN; SAKC167CSL40MCAXT; SP000103490

Oscillator Watchdog
The Oscillator Watchdog (OWD) monitors the clock signal generated by the on-chip
oscillator (either with a crystal or via external clock drive). For this operation the PLL
provides a clock signal which is used to supervise transitions on the oscillator clock. This
PLL clock is independent from the XTAL1 clock. When the expected oscillator clock
transitions are missing the OWD activates the PLL Unlock/OWD interrupt node and
supplies the CPU with the PLL clock signal. Under these circumstances the PLL will
oscillate with its basic frequency.
In direct drive mode the PLL base frequency is used directly (
In prescaler mode the PLL base frequency is divided by 2 (
Note: The CPU clock source is only switched back to the oscillator clock after a
The oscillator watchdog can be disabled by setting bit OWDDIS in register SYSCON.
In this case (OWDDIS = ‘1’) the PLL remains idle and provides no clock signal, while the
CPU clock signal is derived directly from the oscillator clock or via prescaler or SDD. Also
no interrupt request will be generated in case of a missing oscillator clock.
Note: At the end of a reset bit OWDDIS reflects the inverted level of pin RD at that time.
Data Sheet
hardware reset.
Thus the oscillator watchdog may also be disabled via hardware by (externally)
pulling the RD line low upon a reset, similar to the standard reset configuration via
PORT0.
34
f
CPU
f
CPU
= 1 … 2.5 MHz).
= 2 … 5 MHz).
C167CS-4R
V2.2, 2001-08
C167CS-L