MC68HC16Z1CEH16 Freescale Semiconductor, MC68HC16Z1CEH16 Datasheet - Page 112

• Manufacturer Part Number: MC68HC16Z1CEH16
• Description: IC MCU 16BIT 16MHZ 132-PQFP
• Manufacturer: Freescale Semiconductor
• Series: HC16r

Specifications of MC68HC16Z1CEH16

• Core Processor: CPU16
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 132-QFP
• Processor Series: HC16Z
• Core: CPU16
• Data Bus Width: 16 bit
• Controller Family/series: 68HC16
• No. Of I/o's: 26
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• No. Of Timers: 2
• Embedded Interface Type: QSPI, SCI
• Rohs Compliant: Yes
• Package: 132PQFP
• Family Name: HC16
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Number Of Programmable I/os: 16
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 11
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI, UART
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.3.2 Clock Synthesizer Operation
5-6
If a fast or slow reference frequency is provided to the PLL from a source other than a
crystal, or an external system clock signal is applied through the EXTAL pin, the XTAL
pin must be left floating.
either a crystal or an externally supplied reference frequency. A separate power
source increases MCU noise immunity and can be used to run the clock when the
MCU is powered down. A quiet power supply must be used as the V
equate external bypass capacitors should be placed as close as possible to the
V
signal is applied and the PLL is disabled, V
supply.
A voltage controlled oscillator (VCO) in the PLL generates the system clock signal. To
maintain a 50% clock duty cycle, the VCO frequency (f
the system clock frequency, depending on the state of the X bit in SYNCR. The clock
signal is fed back to a divider/counter. The divider controls the frequency of one input
to a phase comparator. The other phase comparator input is a reference signal, either
from the crystal oscillator or from an external source. The comparator generates a con-
trol signal proportional to the difference in phase between the two inputs. This signal
is low-pass filtered and used to correct the VCO output frequency.
Filter circuit implementation can vary, depending upon the external environment and
required clock stability.
works. XFC pin leakage must be kept as low as possible to maintain optimum stability
and PLL performance.
An external filter network connected to the XFC pin is not required when an external
system clock signal is applied and the PLL is disabled (MODCLK = 0 at reset). The
XFC pin must be left floating in this case.
V
DDSYN
DDSYN
pin to assure a stable operating frequency. When an external system clock
is used to power the clock circuits when the system clock is synthesized from
The standard filter used in normal operating environments is a single
0.1 f capacitor, connected from the XFC pin to the V
pin. An alternate filter can be used in high-stability operating environ-
ments to reduce PLL jitter under noisy system conditions. Current
systems that are operating correctly may not require this filter. If the
PLL is not enabled (MODCLK = 0 at reset), the XFC filter is not re-
quired. Versions of the SIM that are configured for either slow or fast
reference use the same filter component values.
Freescale Semiconductor, Inc.
For More Information On This Product,
Figure 5-5
SYSTEM INTEGRATION MODULE
Go to: www.freescale.com
shows two recommended system clock filter net-
NOTE
DDSYN
should be connected to the V
VCO
) is either two or four times
DDSYN
DDSYN
M68HC16 Z SERIES
USER’S MANUAL
supply
source. Ad-
DD