PIC18F4431-E/PT Microchip Technology, PIC18F4431-E/PT Datasheet - Page 241

• Manufacturer Part Number: PIC18F4431-E/PT
• Description: IC MCU FLASH 8KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4431-E/PT

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.4.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RC7/RX/DT/SDO pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 19-12:
 2003 Microchip Technology Inc.
RC7/RX/DT/SDO
RC6/TX/CK/SS
RC6/TX/CK/SS
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
Note:
(SCKP = 0)
(SCKP = 1)
(Interrupt)
CREN bit
bit SREN
SREN bit
RCIF bit
RXREG
Write to
Read
USART SYNCHRONOUS MASTER
RECEPTION
pin
pin
pin
Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
Q2
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
bit0
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit1
PIC18F2331/2431/4331/4431
bit2
Preliminary
bit3
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
Ensure bits CREN and SREN are clear.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
If a single reception is required, set bit SREN.
For continuous reception, set bit CREN.
Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
the enable bit RCIE was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
bit CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit4
bit5
bit6
bit7
DS39616B-page 239
Q1 Q2 Q3 Q4
‘0’