STEVAL-IFS003V1 STMicroelectronics, STEVAL-IFS003V1 Datasheet - Page 9

• Manufacturer Part Number: STEVAL-IFS003V1
• Description: BOARD STLM75/STDS75/ST72F651
• Manufacturer: STMicroelectronics

Specifications of STEVAL-IFS003V1

• Design Resources: STEVAL-IFS003V1 Gerber Files STEVAL-IFS003V1 Schematic STEVAL-IFS003V1 Bill of Materials
• Sensor Type: Temperature
• Sensing Range: -55°C ~ 125°C
• Interface: I²C
• Voltage - Supply: 7.5 V ~ 19 V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ST72F651, STDS75, STLM75
• Silicon Manufacturer: ST Micro
• Silicon Core Number: STLM75/STDS75 And ST72F651AR6
• Kit Application Type: Sensing - Temperature
• Application Sub Type: Temperature Sensor
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Sensitivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6238

PIN DESCRIPTION (Cont’d)
Legend / Abbreviations:
Type: I = input, O = output, S = supply
V
ply rail, supplied by V
In/Output level: C
input trigger
Output level: HS = High Sink (on N-buffer only)
Table 1. Device Pin Description
Pin
10
11
12
13
14
DDF
1
2
3
4
5
6
7
8
9
USBV
USBDM
USBDP
USBVCC
USBV
V
V
PE5/DTC
PE6/DTC
PE7/DTC
PB0/DTC
PB1/DTC
PB2/DTC
PB3/DTC
powered: I/O powered by the alternate sup-
DDF
SSF
Pin Name
SS
DD
T
= CMOS 0.3V
DDF
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
S
S
S
S
and V
X
X
X
X
X
X
X
X
X
CT
CT
CT
CT
C
C
C
SSF
Level
T
T
T
DD
.
HS X
HS X
HS X
/0.7V
X
X
X
X
2)
Input
Port / Control
DD
Doc ID 7215 Rev 4
with
X
Output
X
X
2)
X
X
X
X
X
X
X
Port and control configuration:
– Input:float = floating, wpu = weak pull-up, int = in-
– Output: OD = open drain, T = true open drain, PP
Refer to
on the software configuration of the I/O ports.
The RESET configuration of each pin is shown in
bold.
terrupt
= push-pull, OP = pull-up enabled by option byte.
(after reset)
USB Digital ground
USB bidirectional data (data -)
USB bidirectional data (data +)
USB power supply, output by the on-chip USB 3.3V
linear regulator.
Note: An external decoupling capacitor (typ. 100nF,
min 47nF) must be connected between this pin and
USBV
USB Power supply voltage (4V - 5.5V) also used by
the regulator and PLL
Note: External decoupling capacitors (typ.
4.7µF+100nF, min 2.2µF+100nFmust be connected
between this pin and USBV
Power Line for alternate supply rail. Can be used as
input (with external supply) or output (when using the
on-chip voltage regulator). Note: An external decou-
pling capacitor (min. 20nF) must be connected to this
pin to stabilize the regulator.
Ground Line for alternate supply rail. Can be used as
input (with external supply) or output (when using the
on-chip voltage regulator)
Port E5
Port E6
Port E7
Port B0
Port B1
Port B2
Port B3
Function
Main
“I/O PORTS” on page 45
SS
.
DTC I/O with serial capability
(MMC_CMD)
DTC I/O with serial capability
(MMC_DAT)
DTC I/O with serial capability
(MMC_CLK)
DTC
DTC
DTC
DTC
Alternate Function
SS
.
for more details
ST72651AR6
9/161
1