STEVAL-IFS003V1 STMicroelectronics, STEVAL-IFS003V1 Datasheet - Page 35

• Manufacturer Part Number: STEVAL-IFS003V1
• Description: BOARD STLM75/STDS75/ST72F651
• Manufacturer: STMicroelectronics

Specifications of STEVAL-IFS003V1

• Design Resources: STEVAL-IFS003V1 Gerber Files STEVAL-IFS003V1 Schematic STEVAL-IFS003V1 Bill of Materials
• Sensor Type: Temperature
• Sensing Range: -55°C ~ 125°C
• Interface: I²C
• Voltage - Supply: 7.5 V ~ 19 V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ST72F651, STDS75, STLM75
• Silicon Manufacturer: ST Micro
• Silicon Core Number: STLM75/STDS75 And ST72F651AR6
• Kit Application Type: Sensing - Temperature
• Application Sub Type: Temperature Sensor
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Sensitivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6238

POWER SUPPLY MANAGEMENT (Cont’d)
6.4.3 Storage Media Interface I/Os
The microcontroller is able to drive Storage Media
through an interface operating at a different volt-
age from the rest of the circuit.
This is achieved by powering the Storage Media
interface I/O circuitry through a specific supply rail
connected to V
either as an input or output.
If the on-chip voltage regulator is off, power to the
interface I/Os should be provided externally to the
V
Alone Mode, or in USB mode when the current re-
quired to power the Storage Media is above the
current capacity of the on-chip regulator.
If the on-chip voltage regulator is on, it powers the
interface I/Os, and V
age Media. This is recommended in USB Mode,
when the current required to power the Storage
Media is within the capacity of the on-chip regula-
tor.
Caution: If VDDF is supplied externally, the regu-
lator must not be enabled.
Important Note:
If V
be used and are tied to ground. Refer to
9.2.4
Application Example:
Stand-Alone Mode
– The Storage Media interface supply is powered
DDF
by V
nects V
any True Open Drain I/O pin and controlled by
user software.
DDF
for more details.
pin. This should be the case when in Stand-
DD
is not present, all V
enabled by an external switch which con-
DD
to V
DDF
DDF
pin. The V
. This switch can be driven by
DDF
pin can supply the Stor-
DDF
DDF
-driven I/Os cannot
pin can be used
Section
Doc ID 7215 Rev 4
– The on-chip voltage regulator must be disabled
USB Mode
– In this case the core of the microcontroller is run-
– The Storage Media Interface can be powered
– The regulator output voltage can be pro-
– Should the current requirement for the Storage
Caution: The user should ensure that V
not exceed the maximum rating specified for the
Storage Media V
AGE switch on.
to avoid any conflict and to decrease consump-
tion (reset the REGEN bit in the PCR register).
ning from the USB bus power or the self power
supply. V
a voltage from 4.0 to 5.5V.
through the on-chip regulator (providing power to
the I/O pins and output on pin V
requirement is within the output capacity of the
on chip regulator.
grammed to 2.8V, 3.3V, 3.4V or 3.5 Volts, de-
pending on the Storage Media specifications.
(see VSET[1:0] bits in PCR register description)
Media be higher than the current capacity of the
on chip regulator, an external regulator should be
used. Thus the on-chip voltage regulator must be
disabled to avoid any conflict (reset the REGEN
bit in the PCR register).
DD
and USBV
DDF
max when switching STOR-
DD
pins are supplied with
DDF
ST72651AR6
) if the current
DD
35/161
does
1