ATTINY24A-PU Atmel, ATTINY24A-PU Datasheet - Page 167

• Manufacturer Part Number: ATTINY24A-PU
• Description: MCU AVR 2K FLASH 20MHZ 14PDIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 20 Channel
• Data Rom Size: 128 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 20
• Height: 5.33 mm
• Length: 19.68 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Width: 7.11 mm
• For Use With: ATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.7.1
8183C–AVR–03/11
Enter High-voltage Serial Programming Mode
The following algorithm puts the device in High-voltage Serial Programming mode:
If the rise time of the V
tive algorithm can be used:
Table 19-15. High-voltage Reset Characteristics
Supply Voltage
V
4.5V
5.5V
1. Set Prog_enable pins listed in
2. Apply 4.5 - 5.5V between V
3. Wait 20 - 60 µs, and apply 11.5 - 12.5V to RESET.
4. Keep the Prog_enable pins unchanged for at least 10 µs after the High-voltage has
5. Release the Prog_enable[2] pin after t
6. Wait at least 300 µs before giving any serial instructions on SDI/SII.
7. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
1. Set Prog_enable pins listed in
2. Apply 4.5 - 5.5V between V
3. Monitor V
4. Keep the Prog_enable pins unchanged for at least 10 µs after the High-voltage has
5. Release the Prog_enable[2] pin to avoid drive contention on the Prog_enable[2]/SDO
6. Wait until V
7. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
CC
to 0V.
the next 20 µs.
been applied to ensure the Prog_enable Signature has been latched.
to 0V.
been applied to ensure the Prog_enable Signature has been latched.
pin.
SDI/SII.
CC
CC
, and as soon as V
actually reaches 4.5 - 5.5V before giving any serial instructions on
RESET Pin High-voltage Threshold
CC
is unable to fulfill the requirements listed above, the following alterna-
CC
CC
V
and GND. Ensure that V
and GND.
11.5V
11.5V
Table 19-14 on page 166
Table 19-14 on page 166
CC
HVRST
reaches 0.9 - 1.1V, apply 11.5 - 12.5V to RESET.
HVRST
has elapsed.
ATtiny24A/44A/84A
CC
Minimum High-voltage Period for
to “000”, RESET pin and V
to “000”, RESET pin and V
reaches at least 1.8V within
Latching Prog_enable
100 ns
100 ns
t
HVRST
CC
CC
167