ST92F150-EVAL STMicroelectronics, ST92F150-EVAL Datasheet - Page 306
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
ST92F150-EVAL
Manufacturer Part Number
ST92F150-EVAL
Description
BOARD EVALUATION FOR ST9 SERIES
Manufacturer
STMicroelectronics
Specifications of ST92F150-EVAL
Processor To Be Evaluated
ST90158 and ST92F1x Daughter Board
Interface Type
I2C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
497-2905
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 306 of 429
- Download datasheet (8Mb)
J1850 Byte Level Protocol Decoder (JBLPD)
J1850 BYTE LEVEL PROTOCOL DECODER (Cont’d)
Bit 3 = RDT Receive Data Type.
The RDT bit indicates the type of data which is in
the RXDATA register: message byte or IFR byte.
Any byte received after an SOF but before an
EODM is considered a message byte type. Any
byte received after an SOF, EODM and NBx is an
IFR type.
RDT gets set or cleared at the same time that
RDRF gets set.
RDT is cleared on reset or while CONTROL.JE is
reset, or while CONTROL.JDIS bit is set.
0: Last RXDATA byte was a message type byte
1: Last RXDATA byte was a IRF type byte
Bit 2 = EODM End of Data Minimum Flag.
The EODM flag is set when the JBLPD decoded
VPWI pin has been in a passive state for longer
that the minimum Tv3 symbol time unless the
EODM is inhibited by a sleep, filter or CRCE, IBD,
IFD or RBRK error condition during a frame.
EODM bit does not get set when in the sleep mode
or when a message is filtered.
The EODM bit can be cleared by software writing a
logic “zero” in the EODM position. EODM is
cleared on reset, while CONTROL.JE is reset or
while CONTROL.JDIS bit is set.
If the EODM_M bit of the IMR register is set, when
this bit is set an interrupt request occurs.
0: No EOD symbol detected
1: EOD symbol detected
Note: The EODM bit is not an error flag. It means
that the minimum time related to the passive Tv3
symbol is passed.
Bit 1 = EOFM End of Frame Minimum Flag.
The EOFM flag is set when the JBLPD decoded
VPWI pin has been in a passive state for longer
that the minimum Tv4 symbol time. EOFM will still
get set at the end of filtered frames or frames
where sleep mode was invoked. Consequently,
multiple EOFM flags may be encountered be-
tween frames of interest.
The EOFM bit can be cleared by software writing a
logic “zero” in the EOFM position. EOFM is
cleared on reset, while CONTROL.JE is reset or
while CONTROL.JDIS bit is set.
If the EOFM_M bit of the IMR register is set, when
this bit is set an interrupt request occurs.
0: No EOF symbol detected
1: EOF symbol detected
Note: The EOFM bit is not an error flag. It means
that the minimum time related to the passive Tv4
symbol is passed.
306/429
9
Bit 0 = IDLE Idle Bus Flag
IDLE is set when the JBLPD decoded VPWI pin
recognized an IFS symbol. That is, an idle bus is
when the bus has been in a passive state for long-
er that the Tv6 symbol time. The IDLE flag will re-
main set as long as the decoded VPWI pin is pas-
sive. IDLE is cleared when the decoded VPWI pin
transitions to an active state.
Note that if the VPWI pin remains in a passive
state after JE is set, then the IDLE bit may go high
sometime before a Tv6 symbol is timed on VPWI
(since VPWI timers may be active when JE is
clear).
IDLE is cleared on reset or while the CON-
TROL.JDIS bit is set.
0: J1850 bus not in idle state
1: J1850 bus in idle state
JBLPD TRANSMIT DATA REGISTER (TXDATA)
R241- Read/Write
Register Page: 23
Reset Value: xxxx xxxx (xxh)
The TXDATA register is an eight bits read/write
register in which the data to be transmitted must
be placed. A write to TXDATA merely enters a
byte into the register. To initiate an attempt to
transmit the data, the TXOP register must also be
written. When the TXOP write occurs, the TRDY
flag is cleared. While the TRDY bit is clear, the
data is still in the TXDATA register, so writes to the
TXDATA register with TRDY clear will overwrite
existing TXDATA. When the TXDATA is trans-
ferred to the shift register, the TRDY bit is set
again.
Reads of the TXDATA register will always return
the last byte written.
TXDATA contents are undefined after a reset.
Note: The correct sequence to transmit is to write
first the TXDATA register (if datum is needed) and
then the TXOP one.
Only using the DMA, the correct sequence of writ-
ing operations is first the TXOP register and then
the TXDATA one (if needed).
TXD7
7
TXD6
TXD5
TXD4
TXD3
TXD2
TXD1
TXD0
0
Related parts for ST92F150-EVAL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ST92F150-EPB/US](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
BOARD PROGRAM FOR ST92F150 MCU
Manufacturer:
STMicroelectronics
Datasheet:
![ST92F150-EMU2](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
BOARD EMULATOR FOR ST9 SERIES
Manufacturer:
STMicroelectronics
Datasheet:
![ST92F150-DBE](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools ST9 Dedication Board
Manufacturer:
STMicroelectronics
Datasheet:
![HCF4040BF](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
![HCF4054BF](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
![STEVAL-MKI062V2](/photos/28/39/283999/steval-mki062v2_tmb.jpg)
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
![BUT32V](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
![STTA12006TV2](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
![E110NS20FD](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
![MDS50-800](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
![MDS35-800](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
![E16N100](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet: