LH28F800BJE-PTTL90 Sharp Microelectronics, LH28F800BJE-PTTL90 Datasheet - Page 5

no-image

LH28F800BJE-PTTL90

Manufacturer Part Number
LH28F800BJE-PTTL90
Description
IC FLASH 8MBIT 90NS 48TSOP
Manufacturer
Sharp Microelectronics
Datasheet

Specifications of LH28F800BJE-PTTL90

Format - Memory
FLASH
Memory Type
FLASH
Memory Size
8M (1M x 8 or 512K x 16)
Speed
90ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
425-1821
LHF80J01

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LH28F800BJE-PTTL90
Manufacturer:
SHARP
Quantity:
1 900
Part Number:
LH28F800BJE-PTTL90
Manufacturer:
SHARP/PBF
Quantity:
164
Part Number:
LH28F800BJE-PTTL90
Manufacturer:
SHARP
Quantity:
20 000
1 INTRODUCTION
This datasheet contains the product specifications. Section
1 provides a flash memory overview. Sections 2, 3, 4 and
5 describe the memory organization and functionality.
Section 6 covers electrical specifications.
1.1 Features
Key enhancements of the product are:
Please note following:
1.2 Product Overview
The product is a high-performance 8M-bit Boot Block
Flash memory organized as 512K-word of 16 bits or 1M-
byte of 8 bits. The 512K-word/1M-byte of data is arranged
in two 4K-word/8K-byte boot blocks, six 4K-word/8K-
byte parameter blocks and fifteen 32K-word/64K-byte
main blocks which are individually erasable, lockable and
unlockable in-system. The memory map is shown in
Figure 3.
The dedicated V
when V
A Command User Interface (CUI) serves as the interface
between the system processor and internal operation of the
device. A valid command sequence written to the CUI
initiates device automation. An internal Write State
Machine (WSM) automatically executes the algorithms
and timings necessary for block erase, full chip erase,
word/byte write and lock-bit configuration operations.
•Single low voltage operation
•Low power consumption
•Enhanced Suspend Capabilities
•Boot Block Architecture
•V
3.6V block erase, full chip erase, word/byte write and
lock-bit configuration operations. The V
transitions to GND is recommended for designs that
switch V
CCWLK
CCW
CCW
≤V
has been lowered to 1.0V to support 2.7V-
CCWLK
CCW
off during read operation.
.
pin gives complete data protection
CCW
voltage
A block erase operation erases one of the device’s 32K-
word/64K-byte blocks typically within 1.2s (3V V
V
V
can be independently erased minimum 100,000 times.
Block erase suspend mode allows system software to
suspend block erase to read or write data from any other
block.
Writing memory data is performed in word/byte
increments of the device’s 32K-word blocks typically
within 33µs (3V V
typically within 31µs (3V V
blocks typically within 36µs (3V V
byte blocks typically within 32µs (3V V
Word/byte write suspend mode enables the system to read
data or execute code from any other flash memory array
location.
Individual block locking uses a combination of bits, thirty-
nine block lock-bits, a permanent lock-bit and WP# pin, to
lock and unlock blocks. Block lock-bits gate block erase,
full chip erase and word/byte write operations, while the
permanent lock-bit gates block lock-bit modification and
locked
operations (Set Block Lock-Bit, Set Permanent Lock-Bit
and Clear Block Lock-Bits commands) set and cleared
lock-bits.
The status register indicates when the WSM’s block erase,
full chip erase, word/byte write or lock-bit configuration
operation is finished.
The RY/BY# output gives an additional indicator of WSM
activity by providing both a hardware signal of status
(versus software polling) and status masking (interrupt
masking for background block erase, for example). Status
polling using RY/BY# minimizes both CPU overhead and
system power consumption. When low, RY/BY# indicates
that the WSM is performing a block erase, full chip erase,
word/byte write or lock-bit configuration. RY/BY#-high Z
indicates that the WSM is ready for a new command,
block erase is suspended (and
inactive), word/byte write is suspended, or the device is in
reset mode.
CCW
CC
, 3V V
), 4K-word/8K-byte blocks typically within 0.6s (3V
block
CCW
) independent of other blocks. Each block
alternation.
CC
, 3V V
CC
CCW
Lock-bit
, 3V V
CC
word/byte write is
), 64K-byte blocks
, 3V V
CC
CCW
, 3V V
configuration
), 4K-word
CCW
Rev. 1.27
CC
CCW
), 8K-
, 3V
).

Related parts for LH28F800BJE-PTTL90