IS46TR16128A-15HBLA2 ISSI, IS46TR16128A-15HBLA2 Datasheet - Page 22

• Manufacturer Part Number: IS46TR16128A-15HBLA2
• Description: DRAM 2G, 1.5v, 1333MT/s 128Mx16 DDR3
• Manufacturer: ISSI

Specifications of IS46TR16128A-15HBLA2

• Rohs: yes
• Data Bus Width: 16 bit
• Organization: 128 M x 16
• Package / Case: FBGA-96
• Memory Size: 2 Gbit
• Maximum Clock Frequency: 933 MHz
• Access Time: 13.125 ns
• Supply Voltage - Max: 1.575 V
• Supply Voltage - Min: 1.425 V
• Maximum Operating Current: 65 mA
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT

DQS,DQS#(DLL_on)
DQS,DQS#(DLL_off)
DQS,DQS#(DLL_off)
DQ(DLL_on)
DQ(DLL_off)
DQ(DLL_off)
IS43/46TR16128A, IS43/46TR16128AL,
IS43/46TR82560A, IS43/46TR82560AL
2.4.2 No Operation (NOP) Command
The No operation (NOP) command is used to instruct the selected DDR3 SDRAM to perform a NOP ( CS# low and
RAS#,CAS#,WE# high). This prevents unwanted commands from being registered during idle or wait states. Operations
already in progress are not affected.
2.4.3 Deselect(DES) Command
The Deselect function (CS# HIGH) prevents new commands from being executed by the DDR3 SDRAM. The DDR3
SDRAM is effectively deselected. Operations already in progress are not affected.
2.4.4 DLL-off Mode
DDR3 DLL-off mode is entered by setting MR1 bit A0 to “1”; this will disable the DLL for subsequent operations until A0 bit
set back to “0”. The MR1 A0 bit for DLL control can be switched either during initialization or later. The DLL-off Mode
operations listed below are an optional feature for DDR3. The maximum clock frequency for DLL-off Mode is specified by
the parameter tCKDLL_OFF. There is no minimum frequency limit besides the need to satisfy the refresh interval, tREFI.
Due to latency counter and timing restrictions, only one value of CAS Latency (CL) in MR0 and CAS Write Latency (CWL)
in MR2 are supported. The DLL-off mode is only required to support setting of both CL=6 and CWL=6. DLL-off mode will
affect the Read data Clock to Data Strobe relationship (tDQSCK) but not the data Strobe to Data relationship (tDQSQ,
tQH). Special attention is needed to line up Read data to controller time domain.
Comparing with DLL-on mode, where tDQSCK starts from the rising clock edge (AL+CL) cycles after the Read command,
the DLL-off mode tDQSCK starts (AL+CL-1) cycles after the read command. Another difference is that tDQSCK may not
be small compared to tCK (it might even be larger than tCK) and the difference between tDQSCKmin and tDQSCKmax is
significantly larger than in DLL-on mode. The timing relations on DLL-off mode READ operation have shown at the
following Timing Diagram (CL=6, BL=8)
Note: The tDQSCK is used here for DQS, DQS, and DQ to have a simplified diagram; the DLL_off shift will affect both timings in the same way and the
skew between all DQ, DQS, and DQS# signals will still be tDQSQ
Integrated Silicon Solution, Inc. – www.issi.com –
Rev. 00A
11/14/2012
Command
Address
CK#
CK
READ
T0
NOP
T1
RL (DLL_off) = AL+(CL-1) = 5
RL (DLL_on) = AL+CL =6 (CL=6,AL=0)
NOP
T2
Figure 2.4.4 DLL-off mode READ Timing Operation
CL=6
NOP
T3
.
NOP
T4
NOP
T5
tDQSCK(DLL_off)_min
NOP
tDQSCK(DLL_off)_max
T6
NOP
T7
NOP
T8
NOP
T9
Don’t Care
22
NOP
T10