NT5DS16M16CS NANOAMP [NanoAmp Solutions, Inc.], NT5DS16M16CS Datasheet - Page 31
![no-image](/images/no-image-200.jpg)
NT5DS16M16CS
Manufacturer Part Number
NT5DS16M16CS
Description
256Mb DDR Synchronous DRAM
Manufacturer
NANOAMP [NanoAmp Solutions, Inc.]
Datasheet
1.NT5DS16M16CS.pdf
(76 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NT5DS16M16CS-5T
Manufacturer:
AD
Quantity:
291
Company:
Part Number:
NT5DS16M16CS-5T
Manufacturer:
NANYA
Quantity:
213
Company:
Part Number:
NT5DS16M16CS-5T
Manufacturer:
NANYA
Quantity:
2 526
Company:
Part Number:
NT5DS16M16CS-5T
Manufacturer:
NANYA
Quantity:
118
Part Number:
NT5DS16M16CS-5T
Manufacturer:
NANYA/南亚
Quantity:
20 000
Part Number:
NT5DS16M16CS-5TI
Manufacturer:
NANYA/南亚
Quantity:
20 000
NanoAmp Solutions, Inc.
Writes
Write bursts are initiated with a Write command, as shown in timing figure Write Command on page 32.
The starting column and bank addresses are provided with the Write command, and Auto Precharge is either enabled or dis-
abled for that access. If Auto Precharge is enabled, the row being accessed is precharged at the completion of the burst. For
the generic Write commands used in the following illustrations, Auto Precharge is disabled.
During Write bursts, the first valid data-in element is registered on the first rising edge of DQS following the write command, and
subsequent data elements are registered on successive edges of DQS. The Low state on DQS between the Write command
and the first rising edge is known as the write preamble; the Low state on DQS following the last data-in element is known as
the write postamble. The time between the Write command and the first corresponding rising edge of DQS (t
with a relatively wide range (from 75% to 125% of one clock cycle), so most of the Write diagrams that follow are drawn for the
two extreme cases (i.e. t
extremes of t
and DQS enters High-Z and any additional input data is ignored.
Data for any Write burst may be concatenated with or truncated with a subsequent Write command. In either case, a continuous
flow of input data can be maintained. The new Write command can be issued on any positive edge of clock following the previ-
ous Write command. The first data element from the new burst is applied after either the last element of a completed burst or
the last desired data element of a longer burst which is being truncated. The new Write command should be issued x cycles
after the first Write command, where x equals the number of desired data element pairs (pairs are required by the 2n prefetch
architecture). Timing figure Write to Write (Burst Length = 4) on page 34 shows concatenated bursts of 4. An example of non-
consecutive Writes is shown in timing figure Write to Write: Max DQSS, Non-Consecutive (Burst Length = 4) on page 35. Full-
speed random write accesses within a page or pages can be performed as shown in timing figure Random Write Cycles (Burst
Length = 2, 4 or 8) on page 36. Data for any Write burst may be followed by a subsequent Read command. To follow a Write
without truncating the write burst, t
(CAS Latency = 2; Burst Length = 4) on page 37.
Data for any Write burst may be truncated by a subsequent (interrupting) Read command. This is illustrated in timing figures
“Write to Read: Interrupting (CAS Latency =2; Burst Length = 8)”, “Write to Read: Minimum D
Write), Interrupting (CAS Latency = 2; Burst Length = 8)”, and “Write to Read: Nominal D
Burst Length = 8)”. Note that only the data-in pairs that are registered prior to the t
and any subsequent data-in must be masked with DM, as shown in the diagrams noted previously.
Data for any Write burst may be followed by a subsequent Precharge command. To follow a Write without truncating the write
burst, t
Data for any Write burst may be truncated by a subsequent Precharge command, as shown in timing figures Write to Pre-
charge: Interrupting (Burst Length = 4 or 8) on page 42 to Write to Precharge: Nominal DQSS (2 bit Write), Interrupting (Burst
Length = 4 or 8) on page 44. Note that only the data-in pairs that are registered prior to the t
array, and any subsequent data in should be masked with DM. Following the Precharge command, a subsequent command to
the same bank cannot be issued until t
In the case of a Write burst being executed to completion, a Precharge command issued at the optimum time (as described
above) provides the same operation that would result from the same burst with Auto Precharge. The disadvantage of the Pre-
charge command is that it requires that the command and address busses be available at the appropriate time to issue the com-
mand. The advantage of the Precharge command is that it can be used to truncate bursts.
DOC # 14-02-044 Rev A ECN # 01-1116
The specifications of this device are subject to change without notice. For latest documentation, see http://www.nanoamp.com
WR
should be met as shown in timing figure Write to Precharge: Non-Interrupting (Burst Length = 4) on page 41.
DQSS
for a burst of four. Upon completion of a burst, assuming no other commands have been initiated, the DQs
DQSS
(min) and t
WTR
RP
(Write to Read) should be met as shown in timing figure Write to Read: Non-Interrupting
DQSS
is met.
(max)). Timing figure Write Burst (Burst Length = 4) on page 33 shows the two
NT5DS64M4CT, NT5DS32M8CT, NT5DS16M16CT
NT5DS64M4CS, NT5DS32M8CS, NT5DS16M16CS
WTR
period are written to the internal array,
QSS
WR
, Interrupting (CAS Latency = 2;
QSS
period are written to the internal
, Odd Number of Data (3 bit
DQSS
) is specified
31