pxf4336 Infineon Technologies Corporation, pxf4336 Datasheet - Page 92
pxf4336
Manufacturer Part Number
pxf4336
Description
Abm Premium Atm Buf Fer Manager
Manufacturer
Infineon Technologies Corporation
Datasheet
1.PXF4336.pdf
(425 pages)
- Current page: 92 of 425
- Download datasheet (5Mb)
ABM-P
PXF 4336 V1.1
Functional Description
Optionally, the ATM cell header may be overwritten with a new value programmed in the
MGT by setting ’LCIOen’ = 1 and ’LCI’ to the desired value in
Register 57 "MGT2" on
Page
281.
A queue is released from its VC-merge group by setting ‘QIDvalid’ = 0 in
Register 44
"QCT1" on Page
261.
It is recommended to set the parameters of the individual queues in a merge group to
equal values, reflecting the desired properties of the outgoing merged VC. In particular,
the user must make sure that all queues of a merge group are assigned to the same SB.
Also, for the optional shaping of a merged VC, the shaping parameters TP, TS, tauS and
Config must be specified for each of the logical queues of the merge group and should
all be equal to the intended shaping parameters of the outgoing merged VC.
The VC-merge shaping mechanism works round robin on a per queue basis with the
changing of the QID going on transparently behind the scene. Hence, viewed from the
outgoing VC, there is no difference between a single queue VBR shaping and a merge
queue VBR shaping. In particular, no cell slot is lost on the transition between queues.
3.4.2.5.2 Dummy Queue
A ‘dummy queue’ (in contrast to a normal queue) is always scheduled by the queue
scheduler according to its associated rates and parameters, even though it does not
contain stored cells. Scheduling a dummy queue results in an ’empty cell cycle’ (no cell
is emitted during this cycle).
Storing cells into a dummy queue is possible, but not recommended, since the cells are
never emitted.
Dummy queues can be used for bandwidth reservation e.g. for subsequent multicast
operation or any other cell insert/multiplier process.
A queue can be configured as a ‘dummy queue’ by setting ’DQac = 1’ and ‘RSall’ = 1 in
Register 44 "QCT1" on Page
261. This may only be done if ’MGconf/DQsch’ = 0 in
Register 45 "QCT2" on Page 264
and the queue is empty (QueueLength = 0).
Data Sheet
92
2001-12-17
Related parts for pxf4336
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Mosfet 20v?300v Power Transistor Power Mosfet
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Power Mosfets
Manufacturer:
Infineon Technologies Corporation
Datasheet: