cy8c5588pvi-115es0 Cypress Semiconductor Corporation., cy8c5588pvi-115es0 Datasheet - Page 41

• Manufacturer Part Number: cy8c5588pvi-115es0
• Description: Cy8c55 Family Data Sheet Programmable System-on-chip Psoc?
• Manufacturer: Cypress Semiconductor Corporation.

The Timer/Counter/PWM peripheral can select from multiple
clock sources, with input and output signals connected through
the DSI routing. DSI routing allows input and output connections
to any device pin and any internal digital signal accessible
through the DSI. Each of the four instances has a compare
output, terminal count output (optional complementary compare
output), and programmable interrupt request line. The
Timer/Counter/PWMs are configurable as free running, one shot,
or Enable input controlled. The peripheral has timer reset and
capture inputs, and a kill input for control of the comparator
outputs. The peripheral supports full 16-bit capture.
Timer/Counter/PWM features include:
■
■
■
■
■
■
■
■
■
■
■
■
Figure 7-37. Timer/Counter/PWM
7.1 I
The I
designed to interface the PSoC device with a two wire I
communication bus. The bus is compliant with Philips ‘The I
Specification’ version 2.1. Additional I
instantiated using Universal Digital Blocks (UDBs) in PSoC
Creator, as required.
To eliminate the need for excessive CPU intervention and
overhead, I
and generation of framing bits. I
or multimaster (Slave and Master). In slave mode, the unit
always listens for a start condition to begin sending or receiving
data. Master mode supplies the ability to generate the Start and
Stop conditions and initiate transactions. Multimaster mode
provides clock synchronization and arbitration to allow multiple
masters on the same bus. If Master mode is enabled and Slave
mode is not enabled, the block does not generate interrupts on
externally generated Start conditions. I
DSI routing and allows direct connections to any GPIO or SIO
pins.
Document Number: 001-44094 Rev. *J
16-bit timer/counter/PWM (down count only)
Selectable clock source
PWM comparator (configurable for LT, LTE, EQ, GTE, GT)
Period reload on start, reset, and terminal count
Interrupt on terminal count, compare true, or capture
Dynamic counter reads
Timer capture mode
Count while enable signal is asserted mode
Free run mode
One-shot mode (stop at end of period)
Complementary PWM outputs with deadband
PWM output kill
Clock
Reset
Enable
Capture
Kill
2
2
C peripheral provides a synchronous two wire interface
C
2
C specific support is provided for status detection
Timer / Counter /
PWM 16-bit
2
C operates as a slave, a master,
2
2
C interfaces can be
C interfaces through the
IRQ
TC / Compare!
Compare
PRELIMINARY
2
C serial
2
C
I
CPU intervention. Additionally the device can wake from low
power modes on a 7-bit hardware address match. If wakeup
functionality is required, I
two special sets of SIO pins.
I
■
■
■
■
■
■
■
■
7.2 Digital Filter Block
Some devices in the CY8C55 family of devices have a dedicated
HW accelerator block used for digital filtering. The DFB has a
dedicated multiplier and accumulator that calculates a 24-bit by
24-bit multiply accumulate in one system clock cycle. This
enables the mapping of a direct form FIR filter that approaches
a computation rate of one FIR tap for each clock cycle. The MCU
can implement any of the functions performed by this block, but
at a slower rate that consumes significant MCU bandwidth.
The PSoC Creator interface provides a wizard to implement FIR
and IIR digital filters with coefficients for LPF, BPF, HPF, Notch
and arbitrary shape filters. 64 pairs of data and coefficients are
stored. This enables a 64 tap FIR filter or up to 4 16 tap filters of
either FIR or IIR formulation.
Figure 7-38. DFB Application Diagram (pwr/gnd not shown)
The typical use model is for data to be supplied to the DFB over
the system bus from another on-chip system data source such
as an ADC. The data typically passes through main memory or
is directly transferred from another chip resource through DMA.
The DFB processes this data and passes the result to another
on chip resource such as a DAC or main memory through DMA
on the system bus.
Data movement in or out of the DFB is typically controlled by the
system DMA controller but can be moved directly by the MCU.
2
2
C provides hardware address detect of a 7-bit address without
C features include:
Routing
Slave and Master, Transmitter, and Receiver operation
Byte processing for low CPU overhead
Interrupt or polling CPU interface
Support for bus speeds up to 1 Mbps (3.4 Mbps in UDBs)
7 or 10-bit addressing (10-bit addressing requires firmware
support)
SMBus operation (through firmware support - SMBus
supported in hardware in UDBs)
7-bit hardware address compare
Wake from low power modes on address match
BUSCLK
Digital
PSoC
®
Digital Filter
5: CY8C55 Family Datasheet
Block
2
C pin connections are limited to the
read_data
write_data
Request
DMA
addr
System
CTRL
DMA
Bus
Page 41 of 102
(PHUB)
Source
(PHUB)
Data
Data
Dest
[+] Feedback
[+] Feedback
[+] Feedback
[+] Feedback