ST72561J9-Auto STMicroelectronics, ST72561J9-Auto Datasheet - Page 189
ST72561J9-Auto
Manufacturer Part Number
ST72561J9-Auto
Description
8-bit MCU for automotive
Manufacturer
STMicroelectronics
Datasheet
1.ST72561R9-AUTO.pdf
(324 pages)
Specifications of ST72561J9-Auto
Hdflash Endurance
100 cycles, data retention 20 years at 55 °C
5 Power Saving Modes
halt, auto wake up from halt, active halt, wait and slow
- Current page: 189 of 324
- Download datasheet (3Mb)
ST72561-Auto
Note:
Bit 4 = LASE LIN Auto Synch Enable.
This bit enables the Auto Synch Unit (ASU). It is set and cleared by software. It is only
usable in LIN Slave mode.
Bit 3 = LHDM LIN Header Detection Method
This bit is set and cleared by software. It is only usable in LIN Slave mode. It enables the
Header Detection Method. In addition if the RWU bit in the
SCICR2 register is set, the LHDM bit selects the Wake-Up method (replacing the WAKE bit).
Bit 2 = LHIE LIN Header Interrupt Enable
This bit is set and cleared by software. It is only usable in LIN Slave mode.
Bit 1 = LHDF LIN Header Detection Flag
This bit is set by hardware when a LIN Header is detected and cleared by a software
sequence (an access to the SCISR register followed by a read of the SCICR3 register). It is
only usable in LIN slave mode.
The header detection method depends on the LHDM bit:
- If LHDM = 0, a header is detected as a LIN synch break.
- If LHDM = 1, a header is detected as a LIN Identifier, meaning that a LIN synch
break field + a LIN synch field + a LIN identifier field have been consecutively received.
Bit 0 = LSF LIN Synch Field State
This bit indicates that the LIN synch field is being analyzed. It is only used in LIN slave
mode. In auto synchronization mode (LASE bit = 1), when the SCI is in the LIN synch field
State it waits or counts the falling edges on the RDI line.
It is set by hardware as soon as a LIN synch break is detected and cleared by hardware
when the LIN synch field analysis is finished (see
software to exit LIN synch state and return to idle mode.
Figure 87. LSF bit set and clear
0: auto synch unit disabled
1: auto synch unit enabled.
0: LIN synch break detection method
1: LIN Identifier field detection method
0: LIN header interrupt is inhibited.
1: An SCI interrupt is generated whenever LHDF = 1.
0: no LIN header detected.
1: LIN header detected.
0: the current character is not the LIN synch field
1: LIN synch field state (LIN synch field undergoing analysis)
LSF bit
11 dominant bits
LINSCI serial communication interface (LIN master/slave)
Doc ID 12370 Rev 8
LIN Synch
Break
LIN Synch
Field
parity bits
Figure
Identifier
Field
87). This bit can also be cleared by
189/324
Related parts for ST72561J9-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH FLASH OR ROM, 10-BIT ADC, 5 TIMERS, SPI, LINSCI(TM), ACTIVE CAN
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: