ST72561J9-Auto STMicroelectronics, ST72561J9-Auto Datasheet - Page 184
ST72561J9-Auto
Manufacturer Part Number
ST72561J9-Auto
Description
8-bit MCU for automotive
Manufacturer
STMicroelectronics
Datasheet
1.ST72561R9-AUTO.pdf
(324 pages)
Specifications of ST72561J9-Auto
Hdflash Endurance
100 cycles, data retention 20 years at 55 °C
5 Power Saving Modes
halt, auto wake up from halt, active halt, wait and slow
- Current page: 184 of 324
- Download datasheet (3Mb)
LINSCI serial communication interface (LIN master/slave)
Note:
15.9.8
184/324
Note: The transmitter can be either a master or a slave (in case of a slave listening to the
If the period desynchronization of the slave is +15% (slave too slow), the character “00h”
which represents a sequence of 9 low bits must not be interpreted as a break character (9
bits + 15% = 10.35). Consequently, a valid LIN Synch break must last at least 11 low bits.
LINSCI clock tolerance when synchronized
When synchronization has been performed, following reception of a LIN synch break, the
LINSCI, in LIN mode, has the same clock deviation tolerance as in SCI mode, which is
explained below:
During reception, each bit is oversampled 16 times. The mean of the 8th, 9th and 10th
samples is considered as the bit value.
Consequently, the clock frequency should not vary more than 6/16 (37.5%) within one bit.
The sampling clock is resynchronized at each start bit, so that when receiving 10 bits (one
start bit, 1 data byte, 1 stop bit), the clock deviation should not exceed 3.75%.
Clock deviation causes
The causes which contribute to the total deviation are:
●
●
●
●
●
All the deviations of the system should be added and compared to the LINSCI clock
tolerance:
D
Figure 86. Bit sampling in reception mode
TRA
RDI LINE
Sample
D
D
D
D
the reception of one complete LIN message assuming that the deviation has been
compensated at the beginning of the message.
D
clock
+ D
TRA
response of another slave).
MEAS
QUANT
REC
TCL
MEAS
: deviation due to the transmission line (generally due to the transceivers)
: deviation due to transmitter error.
: deviation of the local oscillator of the receiver: This deviation can occur during
: error due to the LIN Synch measurement performed by the receiver.
: error due to the baud rate quantization of the receiver.
+D
1
QUANT
2
+ D
3
REC
4
7/16
Doc ID 12370 Rev 8
+ D
5
TCL
6
< 3.75%
7
sampled values
8
One bit time
9
10
11
12
13
6/16
7/16
14
15
ST72561-Auto
16
Related parts for ST72561J9-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH FLASH OR ROM, 10-BIT ADC, 5 TIMERS, SPI, LINSCI(TM), ACTIVE CAN
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: