ST7232AK2-Auto STMicroelectronics, ST7232AK2-Auto Datasheet - Page 42
ST7232AK2-Auto
Manufacturer Part Number
ST7232AK2-Auto
Description
8-bit MCU for automotive, 16 Kbyte Flash, 10-bit ADC, 4 timers, SPI, SCI
Manufacturer
STMicroelectronics
Datasheet
1.ST7232AK2-AUTO.pdf
(201 pages)
Specifications of ST7232AK2-Auto
Hdflash Endurance
100 cycles, data retention
Clock Sources
crystal/ceramic resonator oscillators and bypass for external clock
Four Power Saving Modes
halt, active halt, wait and slow
Main Clock Controller With
real time base, beep and clock-out capabilities
Two 16-bit Timers With
2 input captures, 2 output compares, PWM and pulse generator modes
- Current page: 42 of 201
- Download datasheet (4Mb)
Interrupts
7
7.1
7.2
Note:
42/201
Introduction
Masking and processing flow
Interrupts
The ST7 enhanced interrupt management provides the following features:
●
●
●
This interrupt management is based on:
●
●
●
This enhanced interrupt controller guarantees full upward compatibility with the standard
(not nested) ST7 interrupt controller.
The interrupt masking is managed by the I1 and I0 bits of the CC register and the ISPRx
registers which give the interrupt software priority level of each interrupt vector (see
Table
When an interrupt request has to be serviced:
●
●
●
●
The interrupt service routine should end with the IRET instruction which causes the
contents of the saved registers to be recovered from the stack.
As a consequence of the IRET instruction, the I1 and I0 bits are restored from the stack and
the program in the previous level is resumed.
Hardware interrupts
Software interrupt (TRAP)
Nested or concurrent interrupt management with flexible interrupt priority and level
management:
–
–
–
Bit 5 and bit 3 of the CPU CC register (I1:0)
Interrupt software priority registers (ISPRx)
Fixed interrupt vector addresses located at the high addresses of the memory map
(FFE0h to FFFFh) sorted by hardware priority order
Normal processing is suspended at the end of the current instruction execution
The PC, X, A and CC registers are saved onto the stack
I1 and I0 bits of CC register are set according to the corresponding values in the ISPRx
registers of the serviced interrupt vector
The PC is then loaded with the interrupt vector of the interrupt to service and the first
instruction of the interrupt service routine is fetched (refer to
mapping
9). The processing flow is shown in
Up to 4 software programmable nesting levels
Up to 16 interrupt vectors fixed by hardware
2 non maskable events: reset, TRAP
for vector addresses)
Figure
14.
Table 15: Interrupt
ST7232Axx-Auto
Related parts for ST7232AK2-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH 8K FLASH/ROM, ADC, 4 TIMERS, SPI, SCI INTERFACE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: