ST7232AK2-Auto STMicroelectronics, ST7232AK2-Auto Datasheet - Page 103
ST7232AK2-Auto
Manufacturer Part Number
ST7232AK2-Auto
Description
8-bit MCU for automotive, 16 Kbyte Flash, 10-bit ADC, 4 timers, SPI, SCI
Manufacturer
STMicroelectronics
Datasheet
1.ST7232AK2-AUTO.pdf
(201 pages)
Specifications of ST7232AK2-Auto
Hdflash Endurance
100 cycles, data retention
Clock Sources
crystal/ceramic resonator oscillators and bypass for external clock
Four Power Saving Modes
halt, active halt, wait and slow
Main Clock Controller With
real time base, beep and clock-out capabilities
Two 16-bit Timers With
2 input captures, 2 output compares, PWM and pulse generator modes
- Current page: 103 of 201
- Download datasheet (4Mb)
ST7232Axx-Auto
10.4
10.4.1
10.4.2
Note:
10.4.3
General description
Serial peripheral interface (SPI)
Introduction
The serial peripheral interface (SPI) allows full-duplex, synchronous, serial communication
with external devices. An SPI system may consist of a master and one or more slaves
however the SPI interface can not be a master in a multi-master system.
Main features
●
●
●
●
●
●
●
●
●
In slave mode, continuous transmission is not possible at maximum frequency due to the
software overhead for clearing status flags and to initiate the next transmission sequence.
Figure 46
●
●
●
The SPI is connected to external devices through 4 pins:
●
●
●
●
Full duplex synchronous transfers (on 3 lines)
Simplex synchronous transfers (on 2 lines)
Master or slave operation
Six master mode frequencies (f
f
SS management by software or hardware
Programmable clock polarity and phase
End of transfer interrupt flag.
Write collision, master mode fault and overrun flags
SPI control register (SPICR)
SPI control/status register (SPICSR)
SPI data register (SPIDR)
MISO: master in/slave out data
MOSI: master out / slave in data
SCK: serial clock out by SPI masters and input by SPI slaves
SS: Slave select:
This input signal acts as a ‘chip select’ to let the SPI master communicate with slaves
individually and to avoid contention on the data lines. Slave SS inputs can be driven by
standard I/O ports on the master MCU.
CPU
/2 max. slave mode frequency (see note below)
shows the serial peripheral interface (SPI) block diagram. There are 3 registers:
CPU
/4 max.)
On-chip peripherals
103/201
Related parts for ST7232AK2-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH 8K FLASH/ROM, ADC, 4 TIMERS, SPI, SCI INTERFACE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: