SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 706

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.5.3
Table 39-10. Main Oscillator Characteristics
Notes:
708
Symbol
1/(t
C
C
C
t
I
P
I
ST
DDST
DD ON
ON
CRYSTAL
LEXT
INT
CPMAIN
(8)
1. C
2. R
3. R
4. R
5. R
6. Additional user load capacitance should be subtracted from C
7. The C
8. C
(7)
)
SAM9G10
Main Oscillator Characteristics
pF. All parasitic capacitance, package and board, must be calculated in order to reach 12.5 pF (minimum targeted load for
the oscillator) by taking into account the internal load C
capacitance must be: 12.5 pF - 4.4 pF = 8.1 pF which means that 16.2 pF is the target value (16.2 pF from xin to gnd and
16.2 pF from xout to gnd) If 17.5 pF load is targeted, the sum of pad, package, board and external capacitances must be
17.5 pF - 4.4 pF = 13.1 pF which means 26.2 pF (26.2 pF from xin to gnd and 26.2 pF from xout to gnd).
S
S
S
S
S
INT
is the shunt capacitance.
= 100 to 200 Ω; C
= 50 to 100 Ω; C
= 25 to 50 Ω; C
= 20 to 50 Ω; C
Parameter
Crystal Oscillator Frequency
Crystal Load Capacitance
External Load Capacitance
Internal Load Capacitance
Duty Cycle
Startup Time
Standby Current Consumption
Drive Level
Current Dissipation
includes internal parasitic, package load and internal routing capacitance.
CRYSTAL
value must be specified by the crystal manufacturer. In our case, C
S
S
S
= 2.5 to 3.0 pF; C
= 3.2 to 4.0 pF; C
S
= 2.0 to 2.5 pF; C
= 2.0 to 2.5 pF; C
M
M
M
Conditions
C
C
V
C
C
C
C
Standby mode
@ 3 MHz
@ 8 MHz
@ 16 MHz
@ 20 MHz
@ 3 MHz
@ 8 MHz
@ 16 MHz
@ 20 MHz
= 7 to 5 fF (typ, worst case).
= 10 to 8 fF (typ, worst case).
C
M
DDPLL
= 4 to 3 fF (typ, worst case).
CRYSTAL
CRYSTAL
S
S
S
S
XIN
LEXT
= 2 to 1.5 fF (typ, worst case) using 1 kΩ serial resistor on XOUT.
= 3 pF
= 7 pF
= 7 pF
= 7 pF
= 3 to 3.6V
AT91SAM9G10
= 12.5 pF
= 17.5 pF
(2)
(3)
(1)
(1)
(1)
(1)
(4)
(5)
C
1/(t
1/(t
1/(t
1/(t
CRYSTAL
CPMAIN
CPMAIN
CPMAIN
CPMAIN
INT
. So, to target the minimum oscillator load of 12.5 pF, external
(6) (7)
(6) (7)
) = 3 MHz
) = 8 MHz
) = 16 MHz
) = 20 MHz
LEXT
.
C
XOUT
LEXT
CRYSTAL
12.5
Min
40
3
must be between 12.5 pf and 17.5
16.2
26.2
Typ
230
380
400
550
4.4
16
50
6462B–ATARM–6-Sep-11
Max
17.5
330
530
630
750
20
60
20
15
30
50
50
4
2
2
1
MHz
Unit
µW
ms
pF
pF
pF
pF
µA
µA
%