SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 35

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

10.13 USB
10.14 LCD Controller
6462B–ATARM–6-Sep-11
• Each MCI has two slots, each supporting
• Support for stream, block and multi-block data read and write
• USB Host Port:
• USB Device Port:
• Embedded pad pull-up configurable via USB_PUCR Register located in the MATRIX user
• Single and Dual scan color and monochrome passive STN LCD panels supported
• Single scan active TFT LCD panels supported.
• 4-bit single scan, 8-bit single or dual scan, 16-bit dual scan STN interfaces supported
• Up to 24-bit single scan TFT interfaces supported
• Up to 16 gray levels for mono STN and up to 4096 colors for color STN displays
• 1, 2 bits per pixel (palletized), 4 bits per pixel (non-palletized) for mono STN
• 1, 2, 4, 8 bits per pixel (palletized), 16 bits per pixel (non-palletized) for color STN
• 1, 2, 4, 8 bits per pixel (palletized), 16, 24 bits per pixel (non-palletized) for TFT
• Single clock domain architecture
• Resolution supported up to 1280 x 860
interface
– One slot for one MultiMediaCard bus (up to 30 cards) or
– One SD Memory Card
– Compliance with Open HCI Rev 1.0 specification
– Compliance with USB V2.0 Full-speed and Low-speed Specification
– Supports both Low-speed 1.5 Mbps and Full-speed 12 Mbps USB devices
– Root hub integrated with two downstream USB ports
– Two embedded USB transceivers
– No overcurrent detection
– Supports power management
– Operates as a master on the Bus Matrix
– USB V2.0 full-speed compliant, 12 Mbits per second
– Embedded USB V2.0 full-speed transceiver
– Embedded dual-port RAM for endpoints
– Suspend/Resume logic
– Ping-pong mode (two memory banks) for isochronous and bulk endpoints
– Six general-purpose endpoints:
Endpoint 0: 8 bytes, no ping-pong mode
Endpoint 1, Endpoint 2: 64 bytes, ping-pong mode
Endpoint 3: 64 bytes, no ping-pong mode
Endpoint 4, Endpoint 5: 256 bytes, ping-pong mode
SAM9G10
35