DS21552L+ Maxim Integrated Products, DS21552L+ Datasheet - Page 42
![IC TXRX T1 1-CHIP 5V 100-LQFP](/photos/6/82/68291/406-100-lqfp_sml.jpg)
DS21552L+
Manufacturer Part Number
DS21552L+
Description
IC TXRX T1 1-CHIP 5V 100-LQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.DS21352L.pdf
(137 pages)
Specifications of DS21552L+
Function
Single-Chip Transceiver
Interface
E1, HDLC, J1, T1
Number Of Circuits
1
Voltage - Supply
4.75 V ~ 5.25 V
Current - Supply
75mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
100-LQFP
Includes
DSX-1 and CSU Line Build-Out Generator, HDLC Controller, In-Band Loop Code Generator and Detector
Product
Framer
Number Of Transceivers
1
Data Rate
64 Kbps
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Supply Current (max)
75 mA (Typ)
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Ic Interface Type
Parallel, Serial
Supply Voltage Range
4.75V To 5.25V
Operating Temperature Range
0°C To +70°C
Digital Ic Case Style
LQFP
No. Of Pins
100
Filter Terminals
SMD
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power (watts)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
CCR7: COMMON CONTROL REGISTER 7 (Address=0A Hex)
6.6 REMOTE LOOPBACK
When CCR7.6 is set to a one, the DS21352/552 will be forced into Remote LoopBack (RLB). In this
loopback, data input via the RPOSI and RNEGI pins will be transmitted back to the TPOSO and TNEGO
pins. Data will continue to pass through the receive side framer of the DS21352/552 as it would normally
and the data from the transmit side formatter will be ignored. Please see Figure 3-1 for more details.
SYMBOL
LIUODO
(MSB)
LIRST
LIRST
RESR
LIUSI
TESR
CDIG
RLB
-
POSITION
RLB
CCR7.7
CCR7.6
CCR7.5
CCR7.4
CCR7.3
CCR7.2
CCR7.1
CCR7.0
RESR
NAME AND DESCRIPTION
Line Interface Reset. Setting this bit from a zero to a one will initiate an internal reset
that affects the clock recovery state machine and jitter attenuator. Normally this bit is
only toggled on power–up. Must be cleared and set again for a subsequent reset.
Remote Loopback.
0 = loopback disabled
1 = loopback enabled
Receive Elastic Store Reset. Setting this bit from a zero to a one will minimize the
delay through the receive elastic store. Should be toggled after RSYSCLK has been
applied and is stable. See section 14.3 for details. Do not leave this bit set HIGH.
Transmit Elastic Store Reset. Setting this bit from a zero to a one will maximize the
delay through the transmit elastic store. Transmit data is lost during the reset. Should be
toggled after TSYSCLK has been applied and is stable. See section 14.3for details. Do
not leave this bit set HIGH.
Reserved. Must be set low for proper operation.
Line Interface Synchronization Interface Enable. This control bit determines whether
the line receiver should handle a normal T1 signal or a 1.544MHz synchronization signal.
This control has no affect on the line interface transmitter.
0 = line receiver configured to support a normal T1 signal
1 = line receiver configured to support a synchronization signal
Customer Disconnect Indication Generator. This control bit determines whether the
Line Interface will generate an unframed ...1010... pattern at TTIP and TRING instead of
the normal data pattern.
0 = generate normal data at TTIP & TRING as input via TPOSI & TNEGI
1 = generate a ...1010... pattern at TTIP and TRING
Line Interface Open Drain Option. This control bit determines whether the TTIP and
TRING outputs will be open drain or not. The line driver outputs can be forced open
drain to allow 6Vpeak pulses to be generated or to allow the creation of a very low power
interface.
0 = allow TTIP and TRING to operate normally
1 = force the TTIP and TRING outputs to be open drain
TESR
42 of 137
–
LIUSI
CDIG
LIUODO
(LSB)