PIC18F65K90-I/MR Microchip Technology, PIC18F65K90-I/MR Datasheet - Page 309

• Manufacturer Part Number: PIC18F65K90-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

21.3.7
In Slave mode, the data is transmitted and received as
the external clock pulses appear on SCKx. When the
last bit is latched, the SSPxIF interrupt flag bit is set.
While in Slave mode, the external clock is supplied by
the external clock source on the SCKx pin. This exter-
nal clock must meet the minimum high and low times
as specified in the electrical specifications.
While in Sleep mode, the slave can transmit/receive
data. When a byte is received, the device can be
configured to wake-up from Sleep.
21.3.8
The SSx pin allows a Synchronous Slave mode. The
SPI must be in Slave mode with the SSx pin control
enabled (SSPxCON1<3:0> = 04h). When the SSx pin
is low, transmission and reception are enabled and the
SDOx pin is driven. When the SSx pin goes high, the
SDOx pin is no longer driven, even if in the middle of a
FIGURE 21-4:
 2009-2011 Microchip Technology Inc.
SSx
SCKx
(CKP = 0
CKE = 0)
SCKx
(CKP = 1
CKE = 0)
Write to
SSPxBUF
SDOx
SDIx
(SMP = 0)
Input
Sample
(SMP = 0)
SSPxIF
Interrupt
Flag
SSPxSR to
SSPxBUF
SLAVE MODE
SLAVE SELECT
SYNCHRONIZATION
SLAVE SYNCHRONIZATION WAVEFORM
bit 7
bit 7
bit 6
PIC18F87K90 FAMILY
transmitted byte and becomes a floating output.
External pull-up/pull-down resistors may be desirable
depending on the application.
When the SPI module resets, the bit counter is forced
to ‘0’. This can be done by either forcing the SSx pin to
a high level or clearing the SSPEN bit.
To emulate two-wire communication, the SDOx pin can
be connected to the SDIx pin. When the SPI needs to
operate as a receiver, the SDOx pin can be configured
as an input. This disables transmissions from the
SDOx. The SDIx can always be left as an input (SDIx
function) since it cannot create a bus conflict.
Note 1: When the SPI is in Slave mode, with
2: If the SPI is used in Slave mode, with CKE
the
(SSPxCON1<3:0> = 0100), the SPI
module will reset if the SSx pin is set to
V
set, then the SSx pin control must be
enabled.
DD
bit 7
bit 7
.
SSx
pin
Next Q4 Cycle
after Q2
control
DS39957D-page 309
bit 0
bit 0
enabled