PIC18F65K90-I/MR Microchip Technology, PIC18F65K90-I/MR Datasheet - Page 256

• Manufacturer Part Number: PIC18F65K90-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

PIC18F87K90 FAMILY
19.3
In Compare mode, the 16-bit CCPRx register value is
constantly compared against either the TMR1 or TMR3
register pair value. When a match occurs, the ECCPx
pin can be:
• Driven high
• Driven low
• Toggled (high-to-low or low-to-high)
• Unchanged (that is, reflecting the state of the I/O
The action on the pin is based on the value of the mode
select bits (CCPxM<3:0>). At the same time, the
interrupt flag bit, CCPxIF, is set.
19.3.1
Users must configure the ECCPx pin as an output by
clearing the appropriate TRIS bit.
FIGURE 19-2:
DS39957D-page 256
latch)
Note:
Compare Mode
ECCP PIN CONFIGURATION
Clearing the CCPxCON register will force
the
(depending on device configuration) to the
default low level. This is not the PORTx
I/O data latch.
0
1
ECCPx
COMPARE MODE OPERATION BLOCK DIAGRAM
CCPR1H
TMR1H
TMR3H
C1TSEL0
C1TSEL1
C1TSEL2
Comparator
compare
CCPR1L
TMR1L
TMR3L
output
Compare
Match
latch
Set CCP1IF
(Timer1/Timer3 Reset, A/D Trigger)
19.3.2
Timer1 and/or Timer3 must be running in Timer mode
or Synchronized Counter mode if the ECCP module is
using the compare feature. In Asynchronous Counter
mode, the compare operation will not work reliably.
19.3.3
When the Generate Software Interrupt mode is chosen
(CCPxM<3:0> = 1010), the ECCPx pin is not affected;
only the CCPxIF interrupt flag is affected.
19.3.4
The ECCP module is equipped with a Special Event
Trigger. This is an internal hardware signal generated
in Compare mode to trigger actions by other modules.
The Special Event Trigger is enabled by selecting
the
(CCPxM<3:0> = 1011).
The Special Event Trigger resets the Timer register pair
for whichever timer resource is currently assigned as the
module’s time base. This allows the CCPRx registers to
serve as a programmable Period register for either timer.
The Special Event Trigger can also start an A/D conver-
sion. In order to do this, the A/D Converter must
already be enabled.
Special Event Trigger
CCP1CON<3:0>
Compare
Output
Logic
4
TIMER1/TIMER3 MODE SELECTION
SOFTWARE INTERRUPT MODE
SPECIAL EVENT TRIGGER
Special
 2009-2011 Microchip Technology Inc.
S
R
Q
Output Enable
Event
TRIS
ECCP1 Pin
Trigger
mode